Pelco Camcorder CCC4000 User Manual

®
CCC4000 Series  
CCD Color Camera  
Installation/  
Operation Manual  
C1925M (3/99)  
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com  
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150  
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should only be done by qualified service and installation  
personnel.  
2. Installation shall be done in accordance with all local and national electrical and  
mechanical codes utilizing only approved materials.  
3. Use only installation methods and materials capable of supporting four times the  
maximum specified load.  
The product may bear the following marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
C A U T I O N :  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation  
and operation.  
DESCRIPTION  
The CCC4000 Series CCD color camera combines high resolution imaging with a very  
compact package. This camera features the following:  
1/3-Inch Format Color CCD  
This camera uses a 1/3-inch color CCD (charged coupled device) interline transfer sensing  
element.  
Electronic/Passive Iris Control  
Built-in, 4-pole iris drive connector allows this camera to be used with passive (DC  
controlled) auto-iris lenses. Video drive auto-iris lenses are not supported.  
Lens Compatibility  
The standard CS-mount and built-in DC iris control allows this camera to be used with a  
wide variety of lenses, including C/CS-mount lenses in the following styles: fixed iris,  
manual iris, or passive (DC controlled) auto-iris lenses. C-mount lenses require a C/CS-  
mount adapter. Video drive auto-iris lenses are not supported.  
Automatic Gain Control  
Automatically adjusts the image to compensate for changes in light levels when using fixed  
iris or manual iris lenses.  
AC Line Lock  
Automatically locks the camera to the AC frequency (60 Hz)–when using AC power  
sources–instead of the camera’s internal clock frequency (59.94 Hz) to avoid picture roll  
during camera switching operations.  
AC or DC Power Compatibility  
This camera will automatically adjust to either AC or DC class 2 power supplies.  
MODELS  
CCC4000-2  
NTSC format camera  
CCC4000-2X  
CCC4001-2  
PAL format camera  
Same as CCC4000-2, except electronic shutter disabled  
Pelco Manual C1925M (3/99)  
3
 
LOCATION OF PARTS AND CONTROLS  
FRONT VIEW  
BACK-FOCUS  
LOCKING RING  
CS-MOUNT RING  
1/3-INCH  
CCD ELEMENT  
REAR VIEW  
POWER  
CONNECTOR  
IRIS  
CONNECTOR  
V-PHASE  
ADJUSTMENT  
CAMERA MOUNT  
(1/4-20 UNC)  
VIDEO OUTPUT  
(BNC)  
IRIS CONNECTOR PINOUTS  
POWER CONNECTOR PINOUTS  
AC  
AC  
GND  
DC–  
DC+  
4
3
2
1
PIN 1 = CONTROL COIL + (DAMPING COIL –)  
PIN 2 = CONTROL COIL – (DAMPING COIL +)  
PIN 3 = DRIVE COIL +  
PIN 4 = DRIVE COIL –  
Figure 1. Location of Parts and Controls (Front and Rear)  
4
Pelco Manual C1925M (3/99)  
 
INSTALLATION  
CAMERA MOUNTING  
Mount the camera using a 1/4–20 mounting screw that does not exceed .197" (4.5 mm ±.2  
mm) in length (refer to Figure 2).  
An optional CA1750 Mount Adapter is supplied to attach the camera to a ceiling mount.  
To install the adapter (refer to Figure 3):  
CAUTION: Be  
careful not to dam-  
age the camera by  
1. Place the camera inside the adapter and align the camera mount boss with the  
elongated hole in the adapter.  
screwing the adapter too far  
onto the threaded stud. As  
soon as the stud threads ap-  
pear through the adapter  
captive nut, tighten the  
knurled nut.  
2. Attach the camera to the adapter with the provided 1/4-20 bolt and washers.  
3. Attach the adapter with camera to the 1/4-20 threaded stud on the installed mount  
swivel head. Tighten the knurled nut on the mount against the adapter.  
-inch UNC (20 pitch)  
7 in. (ASA standard)  
Figure 2. Camera Mounting Screw  
Figure 3. CA1750 Mount Adapter  
Pelco Manual C1925M (3/99)  
5
 
POWER REQUIREMENTS  
An external power supply (not provided) is required when using CCC4000 Series cameras.  
This camera will accept either AC or DC power in accordance with the chart immediately  
below. A safety ground terminal ( ) is provided on the connector block to connect the  
camera to ground potential. Maximum voltage between the supply inputs and the safety  
ground must be less than 50 volts. Camera electronics are galvanically insulated from the  
camera supply, which protects a system with more than one camera from ground loop  
problems. The power connector block can be removed from the camera to ease mounting  
and/or installation.  
Model  
AC Power  
DC Power  
CCC4000-2, CCC4001-2  
CCC4000-2X  
12–27.6 VAC @ 60 Hz  
12–24 VAC @ 50 Hz  
10.8–39 VDC (2.7 W)  
10.8–34 VDC (2.7 W)  
POWER AND VIDEO CONNECTIONS  
If you are using AC power and are wiring more than one camera to the same transformer,  
connect one side of the transformer to the same terminal on all cameras, and connect the  
other side of the transformer to the remaining terminal on all cameras. Failure to connect all  
of the cameras the same will cause the cameras to be out of phase with each other and  
may produce what appears to be vertical roll when switching between cameras.  
WARNING: Be  
sure to connect the  
power and ground  
leads to the appropriate ter-  
minals. Wrong connections  
may cause malfunction and/  
or damage to the video  
camera.  
Connect a video cable to the SIGNAL OUT connector (BNC) on the rear of the camera  
(refer to Figure 1). Refer to Table A for the type of video coaxial cable to use.  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
RG11/U  
750 ft (229m)  
1,000 ft (305m)  
1,500 ft (457m)  
* Minimum cable requirements:  
75 ohms  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
6
Pelco Manual C1925M (3/99)  
 
LENS INSTALLATION  
GENERAL LENS INFORMATION  
CCC4000 Series cameras are factory adjusted to the CS-mount standard. Fixed iris,  
manual iris, or passive (DC controlled) auto-iris lenses may be used. Passive (DC  
controlled) auto-iris lenses require a standard 4-pin square connector (type D4-152N, not  
supplied) that is standard on all Pelco lenses.  
C-mount lenses are also compatible by using a Pelco PCMA40 C/CS-mount adapter. Refer  
to Figure 4.  
Important Lens Notes:  
Passive (DC controlled) auto-iris lenses are recommended in outdoor applications to  
control lighting changes and prevent picture smear.  
This camera will not support active (video controlled) auto-iris lenses (having a built-in  
electronic circuit for driving the iris).  
C-MOUNT  
LENS  
C/CS-MOUNT  
CAMERA  
ADAPTER  
Figure 4. C-mount Lens with C/CS-Mount Adapter  
Pelco Manual C1925M (3/99)  
7
 
LENS MOUNTING  
Do not release the back-focus locking ring unnecessarily. Back-focus adjustment has  
been set at the factory to the standard CS-mount back-focus distance.  
To mount a lens:  
1. Remove the black protection cover from the CS-mounting ring.  
2. If using a C-mount lens, mount a C/CS-mount adapter between lens and camera.  
Refer to Figure 4.  
3. Screw the lens on the camera. Be careful to prevent dust from entering the space  
between the lens and the CCD element. If necessary, use clean, compressed air to  
remove any foreign matter.  
4. When using a passive (DC controlled) auto-iris lens, connect the iris cable to the iris  
connector on the back of the camera. Refer to the Auto-Iris Lenses section.  
5. Aim the camera and focus the lens to the object or area to be observed.  
6. If a manual-iris lens is used, adjust the iris for the best picture quality. The largest  
aperture gives the best light sensitivity, the smallest aperture the greatest depth of  
field.  
AUTO-IRIS LENSES  
Passive auto-iris lenses are DC controlled via the 4-pin iris drive connector (type D4-152N)  
located on the back of the camera (refer to Figure 1). When an auto-iris lens is used the  
electronic shutter speed is fixed at 1/60th of a second for EIA-standard cameras or 1/50th  
of a second for CCIR-standard cameras. The electronic shutter speed feature does not  
apply to the CCC4001-2 model since this function has been disabled.  
Pin connections for the iris drive connector are as follows (refer to Figure 1):  
pin 1  
pin 2  
pin 3  
pin 4  
control coil + (damping coil -)  
control coil - (damping coil +)  
drive coil +  
drive coil -  
BACK-FOCUS ADJUSTMENT  
NOTE: The iris cable of a  
(passive) auto-iris lens pre-  
vents the lens being rotated  
more than 180 degrees. In  
this case, disconnect the iris  
cable, rotate the lens a full  
turn, reconnect the iris cable  
and continue the adjust-  
ment.  
Do not release the back-focus locking ring unnecessarily. Back-focus adjustment has  
been set at the factory to the standard CS-mount back-focus distance.  
Back-focus is defined as the distance between the lens optics and the camera’s CCD  
sensing element.  
Accurate back-focus becomes most critical when tracking stationary objects with a  
motorized zoom lens. In rare cases, however, a camera that gives an unsharp picture using  
a particular lens may require back-focus adjustment.  
Fixed Focal Length Lenses  
NOTE: When adjusting  
back-focus with an auto-iris  
lens, the iris cable must be  
plugged into the iris drive  
connector; otherwise, the  
iris will not open.  
1. With the camera operating, position the camera to view the intended object.  
2. Set the focus ring, if present, to infinity ().  
3. Set the lens iris to its widest usable opening. Use a neutral density filter with auto-iris  
lenses in outdoor or bright light settings to ensure maximum iris opening during back-  
focus adjustment. When a neutral density filter is not available, point the camera to a  
relatively dark area to obtain the greatest iris opening.  
4. Adjust the back-focus.  
a. Turn the back-focus locking ring counterclockwise to loosen the CS-mount ring.  
8
Pelco Manual C1925M (3/99)  
 
b. Adjust the lens and the CS-mount ring together until picture is sharpest.  
c. Hold the lens and CS-mount ring in place and turn the back-focus locking  
ring clockwise to tighten.  
Motorized Zoom Lenses  
1. With the camera operating, position the camera to view an object at a distance not  
less than 45 feet (15 meters) away.  
2. Using the camera controller, set the lens in the following manner:  
a. Zoom out as far as possible (zoom wide).  
b. Focus on the distant object (focus far).  
c. Open the iris as wide as possible (iris open). Use a neutral density filter with  
auto-iris lenses in outdoor or bright light settings to ensure maximum iris opening  
during back-focus adjustment. When a neutral density filter is not available, point  
the camera to a relatively dark area to obtain the greatest iris opening.  
3. Adjust back-focus until the object is in sharpest focus.  
a. Turn the back-focus locking ring counterclockwise to loosen the CS-mount ring.  
b. Adjust the lens and the CS-mount ring together until picture is sharpest.  
c. Hold the lens and CS-mount ring in place and turn the back-focus locking ring  
clockwise to tighten.  
4. Zoom in all the way on the distant object, then focus the lens for best picture.  
5. Zoom out all the way while observing the focus on the monitor (known as “tracking”). If  
the image stays in focus throughout the entire zoom range, the back-focus is correct.  
Otherwise repeat the process beginning with step 1.  
CAMERA SYNCHRONIZATION AND V-PHASE  
When using a DC power supply, synchronization is internally locked and V-phase control is  
inoperative.  
V-phase adjustment is unnecessary when using AC power with a single camera.  
When powering more than one camera with AC, phase differences may occur as a result of  
being connected to different power groups. These phase differences become apparent as a  
brief rolling of the picture each time cameras are switched, known as vertical roll.  
Vertical roll can be corrected by synchronizing the cameras using the V-phase control  
button inside the opening on the back of the camera (refer to Figure 1). Each time the  
V-phase button is pressed, the line lock position shifts by 60 degrees.  
The CCC4000 Series cameras generate a video signal with synchronization pulses  
corresponding to the following:  
CCC4000-2  
CCC4000-2X  
CCC4001-2  
NTSC Standard  
PAL Standard  
NTSC Standard  
V-PHASE ADJUSTMENT  
Generally, it is necessary to have two people in communication when cameras are  
synchronized: one person at the camera to be synchronized and a person at the monitor to  
observe the vertical “roll” and the effect of any adjustments made at the camera.  
1. Choose a camera to which all of the other cameras will be synchronized. Go through  
the available cameras and determine the best camera to which the others should be  
synchronized.  
Pelco Manual C1925M (3/99)  
9
 
2. Select a second camera that is out of synchronization with the first camera.  
3. To shift the V-phase, use a sharp pencil, a toothpick, or some other pointed device  
capable of being inserted into the V-phase adjustment opening. Each press of the V-  
phase button will shift the AC linelock by 60 degrees.  
4. Switch the cameras back and forth, observing the “roll” between the cameras when  
they are switched.  
5. If “roll” is present, press the V-phase button again, observing the “roll” each time an  
adjustment is made.  
6. Repeat this process as many times as necessary and for each of the other cameras in  
the system.  
TROUBLESHOOTING  
The following conditions may be observed when using a CCD camera and are not  
necessarily a fault of the camera.  
Vertical smear  
This may occur when viewing a bright object or an intense  
reflection.  
Patterned noise and blemish A fixed pattern may appear over the entire monitor screen  
when the camera is operated at a high temperature.  
Jagged picture  
Becomes noticeable when viewing stripes, straight lines, or  
similar patterns.  
Camera does not operate  
There are no serviceable parts on CCC4000 Series  
cameras. If a camera fails to function properly, confirm that  
all necessary connections are in order and that lens  
adjustments are correct for the application.  
MAINTENANCE  
Be careful not to spill water or other liquids on the unit.  
Avoid operating or storing the unit in the following locations:  
Extremely hot or cold places. The operating temperature of CCC4000 Series cameras  
is 14° to 122°F (10° to 50°C).  
Damp or dusty places  
Where it may become exposed to rain  
Locations subject to strong vibrations  
Near generators of powerful electromagnetic radiation such as radio or television  
transmitters  
Remove dust or dirt on the surface of the lens or optical filter with a blower.  
Clean the body with a dry cloth. If it is very dirty, use a cloth dampened with a small quantity  
of neutral detergent, then wipe dry. Avoid the use of volatile solvents such as thinners,  
benzene, alcohol, and insecticides. They may damage the surface finish, or impair the  
operation of the cameras.  
10  
Pelco Manual C1925M (3/99)  
 
SPECIFICATIONS  
CCD Sensor:  
Color 1/3-inch interline transfer  
Pixels  
NTSC:  
PAL:  
512 H x 492 V  
512 H x 582 V  
Sensing Area:  
Sync System:  
4.7 x 3.5 mm (3/16 x 1/8 in.)  
Free running/line lock (when AC powered)  
Horizontal  
Resolution:  
400 TV lines  
Lens Mount:  
CS mount  
Light Sensitivity:  
Electronic Shutter  
3.5 lux (50 ire/-6 dB) at f/1.2  
Speed (N/A for the CCC4001-2 model)  
NTSC:  
PAL:  
1/60-1/50,000 sec  
1/50-1/50,000 sec  
Signal to  
Noise Ratio:  
> 50 dB  
Gain Control:  
Automatic  
Power  
Requirements  
PAL:  
NTSC:  
12–24 VAC, 10.8–34 VDC  
12–27.6 VAC, 10.8–39 VDC  
Video Output:  
Lens Jack:  
CVBS, 1 Vp-p, 75 ohms  
4-pin connector (type D4-152N)  
Power  
Consumption  
(camera only):  
2.7 watts maximum  
Operating  
Temperature:  
14° to 122°F (-10° to 50°C)  
20–95% relative humidity  
Conductive-coated ABS  
Humidity:  
Construction:  
Mounting Threads: 1/4-20 UNC  
Dimensions:  
2.75 in. W x 2.88 in. H x 2.38 in. D (70 x 72.5 x 60 mm)  
Weight  
(without lens):  
0.45 lb (200g)  
(Design and product specifications subject to change without notice.)  
Pelco Manual C1925M (3/99)  
11  
 
REGULATORY NOTICES  
NOTE: This equipment has been tested and found to comply with the limits of a Class A  
digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide  
reasonable protection against harmful interference when the equipment is operated in a  
commercial environment. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instruction manual, may cause  
harmful interference to radio communications. Operation of this equipment in a residential  
area is likely to cause harmful interference in which case the user will be required to correct  
the interference at his own expense.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
C1925M  
Date  
1/98  
3/99  
Comments  
Original version.  
Added CCC4001-2 model. Revised manual format.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 1999, Pelco.  
All rights reserved.  
12  
Pelco Manual C1925M (3/99)  
 

Philips Cell Phone Accessories s10 User Manual
Philips Headphones SBCH P1000 User Manual
Philips Portable DVD Player MCD139 User Manual
Philips Satellite TV System DSX 5150 User Manual
Philips Vacuum Cleaner FC9166 9160 User Manual
Pioneer MP3 Docking Station XW NAS5 User Manual
Planar Respiratory Product EL320240 FA3 User Manual
Poulan Chainsaw 530164284 User Manual
Premier Mounts Projector Accessories PBM 070L User Manual
PYLE Audio Car Video System PLRD103F User Manual