Pelco Car Video System PMCL400 Series User Manual

I N S T A L L A T I O N / O P E R A T I O N  
PMCL400 Series  
TFT LCD Monitor  
C2927M-D (9/09)  
 
Contents  
C2927M-D (9/09)  
3
 
List of Illustrations  
4
C2927M-D (9/09)  
 
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one blade wider than the  
other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the  
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from  
the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Only use with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus combination to avoid injury from tip-over.  
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-  
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
14. Unplug the apparatus during lightning storms or when unused for long periods of time.  
15. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.  
16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.  
17. Installation should be done only by qualified personnel and conform to all local codes.  
18. Unless this unit is specifically marked as NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not  
be installed where exposed to rain and moisture.  
19. Only use installation methods and materials capable of supporting four times the maximum specified load.  
20. Only use replacement parts recommended by Pelco.  
21. Avoid touching the screen directly with your fingers as the oils from your skin may be difficult to remove from the LCD.  
22. Do not apply direct pressure on the screen.  
23. Keep the monitor in a dust-free environment and away from strong electromagnetic fields.  
24. Do not use attachments, such as mounts, that are not recommended by Pelco. They may be hazardous.  
25. Do not place the monitor on an unstable stand, bracket, or mount. The unit may fall, causing serious damage to the unit or injury to a  
person. Only use mounts recommended by Pelco.  
26. A CCC-approved power cord must be used to power this equipment when used in China.  
27. A still image displayed too long may cause permanent damage to the LCD panel. Watching the LCD in 4:3 format for a long time may leave  
traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Using a  
camera or a system may cause a similar effect to the screen. Damages caused by this effect are not covered by the warranty.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of electric shock is present  
within this unit.  
CAUTION:  
This symbol indicates that there are important operating and maintenance instructions in the  
lre accompanying this unit  
DO NOT OPEN.  
RISK OF ELECTRIC SHOCK.  
6
C2927M-D (9/09)  
 
 
Important Notices  
LEGAL NOTICE  
SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF  
WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY  
BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU  
ARE SOLELY RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT ADHERENCE TO ANY/ALL RIGHTS OF  
PRIVACY AND PERSONALTY. USE OF THIS EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL BE DEEMED  
UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR  
LICENSE RIGHTS THEREUNDER.  
REGULATORY NOTICES  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This  
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.  
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this  
equipment under Federal Communications Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
C2927M-D (9/09)  
7
 
     
Description  
The PMCL400 Series TFT LCD monitor provides high resolution display of computer signals. These 17-inch and 19-inch monitors use a color, thin  
film transistor (TFT) active matrix LCD panel (1280 x 1024) that automatically adapts to the appropriate input resolution. The RGB and DVI mode  
settings allow the monitor to seamlessly accept a variety of native resolutions, making the PMCL400 Series compatible with lower resolution  
products.  
The PMCL400 Series features an ergonomic design, autoranging internal power supply, and low power consumption. These innovations,  
combined with quick panel response time to minimize ghosting in motion video, make the PMCL400 Series an ideal choice for use with any  
digital video recorder (DVR) or PC application.  
In addition, the PMCL400 Series features a folding picture frame-style desktop stand, optional rack mount kits, and VESA®-compliant mounting  
holes to easily adapt to the available wall and ceiling mounts.  
The on-screen display (OSD) menus and front panel controls provide easy configuration of standard monitor display parameters right on the  
screen. These settings are then stored in the monitor, which eliminates the need for a computer when adjusting basic monitor functions.  
MODELS  
PMCL417A  
PMCL419A  
17-inch (432 mm) active TFT LCD monitor  
19-inch (483 mm) active TFT LCD monitor  
RECOMMENDED MOUNTS  
PMCL-WM  
PMCL-WMT  
LCD flat wall mount for TFT monitors  
LCD tilt wall mount for TFT monitors  
PMCL-WM1A/PMCL-WM2A LCD single-arm and dual-arm swing wall mounts for TFT monitors  
PMCL-CM  
LCD swivel ceiling mount for TFT monitors  
LCD swivel ceiling mount and pole for TFT monitors  
LCD rack mount for 17-inch TFT monitors  
LCD rack mount for 19-inch TFT monitors  
PMCL-CMP  
PMCL-17ARM  
PMCL-19ARM  
8
C2927M-D (9/09)  
 
     
PACKAGE CONTENTS  
Figure 1. Package Contents  
ì
î
ï
ñ
ó
r
s
t
17- or 19-inch TFT LCD Monitor (1 ea.)  
USA Standard Power Cord (1 ea.)  
European Standard Power Cord (1 ea.)  
DVI Cable (1 ea.)  
RGB Cable with 15-pin D-Sub Connection (1 ea.)  
Remote Control Unit (1 ea.)  
AAA Batteries for Remote Control (2 ea.)  
Installation/Operation Manual (1 ea.)  
C2927M-D (9/09)  
9
 
   
Installation  
The monitor can be installed using any of the following options:  
Desktop Stand  
Flat Wall Mounting  
Rack Mounting  
DESK STAND  
The monitor comes with a desktop foot stand attached, so that it can be placed on any flat surface (desk or table). You can manually adjust the  
monitor to the viewing angle you want by repositioning the foot stand on the back of the monitor.  
To detach the stand, remove the four mounting screws from the back of the monitor.  
WALL MOUNTING  
The monitor can be mounted to a wall using one of the following optional mounts: PMCL-WM, PMCL-WMT, PMCL-WM1A, and PMCL-WM2A  
wall mount kits if you want the monitor attached to the wall.  
The PMCL-WM mount has a maximum load capacity of 68 lb (30.8 kg).  
The PMCL-WMT, PMCL-WM1A, and PMCL-WM2A mounts have a maximum load capacity of 90 lb (40.8 kg).  
WARNING: Pelco strongly recommends that a professional installer performs the bracket and LCD monitor installation to ensure the  
proper installation and attachment.  
VESA100  
SCREW M4 X 0.7 X 12 MM  
WALL MOUNT  
(EXCLUDED)  
Figure 2. Attaching the Mount in a Wall Installation  
To mount the monitor to a wall:  
1. Align the screw holes in the wall mount with the mounting holes in the back of the monitor.  
2. Insert and tighten four M4 x 0.7 x 12 mm screws (not supplied).  
3. Refer to the applicable mount manual for instructions on how to attach the mount to the wall.  
10  
C2927M-D (9/09)  
 
       
RACK MOUNTING  
The monitor can be mounted in a rack using the optional PMCL-17ARM or PMCL-19ARM rack mount kit. The weight of the mount is 1.1 lb (0.5 kg)  
and has a maximum load capacity of 22 lb (10 kg).  
To mount the monitor in a rack:  
1. Attach the left and right brackets to the monitor using the eight M4 x 0.7 screws (supplied) with the rack mount kit.  
Figure 3. Installing the Brackets in a Rack Mount Installation  
2. Attach the monitor to the rack (refer to Figure 4):  
a. Position the monitor brackets against the rack. Align the bracket slots with the holes in the rack.  
b. Insert eight screws of an appropriate size (not supplied) through the bracket slots and into the holes in the rack.  
c. Tighten the screws.  
Figure 4. Installing the Monitor in the Rack  
C2927M-D (9/09)  
11  
 
     
REAR PANEL CONNECTORS  
S-VIDEO  
VIDEO 1  
S-VIDEO  
VIDEO  
1
INPUT  
OUTPUT  
INPUT  
OUTPUT  
2
VIDEO  
AUDIO  
1
VIDEO 2  
AUDIO 1  
INPUT OUTPUT  
AUDIO  
2
INPUT OUTPUT  
AUDIO 2  
DVI IN  
RGB IN  
PC AUDIO  
AC IN  
Figure 5. Rear Panel Connectors  
ì
î
ï
ñ
ó
r
s
t
AC IN: Connects power to the unit from a 100 VAC to 240, 50/60 Hz source.  
DVI IN: Provides connection to digital signals from a computer or any Pelco device with DVI output..  
RGB IN: Provides connection to RGB output of a computer or any Pelco device with RGB output.  
PC AUDIO: Provides audio connection from a PC or recording device. The stereo mini jack is to be used in conjunction with the RGB input.  
S-Video (loop through): Connection of S-Video signals from external sources. The video loops through the four-pin DIN S-Video output.  
Video 1 (loop through): Input connections from DVD players or time-lapse VCRs. The video loops through the BNC video output.  
Video 2 (loop through): Input connections from DVD players or time-lapse VCRs. The video loops through the BNC video output.  
Audio 1 (loop through): Mono RCA audio inputs.  
12  
C2927M-D (9/09)  
 
   
Operation  
FRONT PANEL CONTROLS  
MENU SOURCE  
VOL  
Figure 6. Front Panel Controls  
ì
î
ï
ñ
ó
r
s
Menu: Displays the main on-screen menu.  
Source: Selects the input source and confirms your choice.  
and : Navigates through the on-screen menu. Also, is “Auto” in RGB mode  
VOL (and ): Increases or decreases the volume. Also selects or adjusts items in the on-screen menu.  
(remote control signal receiver): Receives remote control signals.  
(power label)  
(power button and power indicator): Turns the monitor on and off. Also indicates the power status. Red indicates that the power is off;  
blue/green indicates that the power is on.  
C2927M-D (9/09)  
13  
 
     
REMOTE CONTROL FUNCTIONS  
MUTE  
POWER  
VIDEO1  
RGB  
VIDEO 2  
DVI  
S-VIDEO  
MENU/EXIT  
/VOL  
AUTO  
/VOL +  
ENTER  
ASPECT  
Figure 7. Remote Control  
POWER: Turns the monitor on and off.  
ì
î
ï
AUTO: Selects auto adjustment of the screen in RGB mode.  
(/VOL– and /VOL+, ,): Increases and decreases the volume. The up and down arrows let you move  
the cursor up and down in the on-screen menu.  
ñ
ó
r
s
t
ASPECT: (PMCL319W only.) Changes the screen’s scan mode (4:3, 16:9).  
ENTER: Confirms (store or enter) your choice in the on-screen menu.  
MENU/EXIT: Displays/exits the on-screen menu.  
(input source): Displays all the available input sources. Press the button to select the desired input source.  
MUTE: Temporarily silences the sound. To return the sound, press MUTE again.  
14  
C2927M-D (9/09)  
 
   
ON-SCREEN DISPLAY FUNCTION  
The PMCL400 Series on-screen display (OSD) lets you easily change the basic functions of the monitor from the front panel or the remote control.  
Figure 8 shows how to change the input source by accessing the menu using the OSD function. The input source name appears in the upper-right  
corner of the menu screen any time the input source is changed or when you press ENTER on the remote control.  
VIDEO 1  
VIDEO 1/2  
S-VIDEO  
RGB  
DVI  
Figure 8. Input Source Name Display  
To access the menus:  
1. Press the MENU button to access the main menu.  
2. Use the up and down arrow buttons (,) to highlight a selection.  
3. Use the left and right arrow buttons (, ) to adjust the setting on a selected item.  
C2927M-D (9/09)  
15  
 
   
VIDEO 1, VIDEO 2, S-VIDEO MODE MENU  
Input Menu  
VIDEO 1  
VIDEO 2  
S-VIDEO  
RGB  
MAIN MENU  
INPUT  
CONTRAST  
BRIGHTNESS  
COLOR  
SHARPNESS  
TINT  
3D NOISE REDUCTION  
LANGUAGE  
OSD SETTING  
COLOR TEMPERATURE  
ISM  
DVI  
Contrast Menu  
100  
0
Brightness Menu  
100  
0
0
Color Menu  
100  
Sharpness Menu  
100  
EDGE ENHANCEMENT  
DYNAMIC CONTRAST  
DEFAULT SETTING  
INFORMATION  
0
0
Tint Menu  
100  
OSD H Position  
OSD V Position  
3D Noise Reduction Menu  
0
0
100  
100  
OFF  
NORMAL  
STRONG  
Language Menu  
ENGLISH  
ITALIAN  
FRENCH  
SPANISH  
GERMAN  
PORTUGUESE  
RUSSIAN  
CHINESE  
OSD Dwelling Time  
OFF  
5
30  
OSD Setting Menu  
OSD Setting Menu  
OSD H. POSITION  
OSD V. POSITION  
OSD DISPLAY TIME  
SETUP  
R-Gain Menu  
G-Gain Menu  
B-Gain Menu  
Reset Setting  
0
0
0
100  
100  
100  
Color Temperature Menu  
NORMAL  
COOL  
User Menu  
R-GAIN  
G-GAIN  
B-GAIN  
RESET  
USER  
ISM Menu  
ON OFF  
0
8
Edge Enhancement Menu  
OFF  
ON  
RESTORE  
Dynamic Contrast Menu  
OFF  
ON  
Default Setting Menu  
RESTORE  
INFORMATION  
Figure 9. Video 1, Video 2, S-Video Mode Menu  
16  
C2927M-D (9/09)  
 
   
The Video 1, Video 2, S-Video Mode menu contains the following features:  
Input: Changes the video input option. Select VIDEO 1, VIDEO 2, or S-VIDEO.  
Contrast: Adjusts the black level of the image (0 to 100).  
Brightness: Adjusts the white level of the image (0 to 100).  
Color: Adjusts the color saturation of the video signal (0 to 100).  
Sharpness: Adjusts the picture softer or sharper (0 to 100).  
Tint: Adjusts the range of color: green to red (0 to 100).  
3-D Noise Reduction: Reduces the video signal’s background noise (NORMAL, STRONG, or OFF). NORMAL is the regular level of noise  
reduction while STRONG increases the level of noise reduction.  
Language: Changes the language selection. Select English, Italian, French, Spanish, German, Portuguese-Brazilian, Russian, or Chinese for the  
OSD display.  
OSD Setting: Select SETUP for the on-screen display. Then select one of the following:  
OSD H.POSITION: Adjusts the OSD horizontal position (0 to 100).  
OSD V.POSITION: Adjusts the OSD vertical position (0 to 100).  
OSD DISPLAY TIME: Adjusts the display time (OFF or 5 to 30 seconds). Selecting 5 or 30 determines how many seconds the display  
remains on the screen when you press a button. Selecting OFF means that there is no delay.  
Color Temperature: Select NORMAL, COOL, or USER. If you select USER, then select from the following:  
R-Gain: Adjusts gain for red (0 to 100).  
G-Gain: Adjusts gain for green (0 to 100).  
B-Gain: Adjusts gain for blue (0 to 100).  
Reset: Select RESTORE to return to the original color temperature settings.  
ISM: (Image sticking minimization) Sets the recovery time of an LCD panel display when screen burn-in occurs (when a fixed image has been  
displayed for a long time). The ISM function starts working after the power is off for 10 minutes. Select ON, OFF, or from 1 to 8 hours for the  
operation period.  
Edge Enhancement: Improves the edge characteristic. The default setting is OFF.  
Dynamic Contrast: Improves the contrast characteristic. The default setting is ON.  
Default Setting: Select RESTORE to reset the monitor to the default settings.  
Information: Select INFORMATION to access Pelco headquarters information.  
C2927M-D (9/09)  
17  
 
RGB AND DVI MODE MENU  
Input Menu  
VIDEO 1  
VIDEO 2  
S-VIDEO  
RGB  
MAIN MENU  
DVI  
Contrast Menu  
100  
INPUT  
CONTRAST  
BRIGHTNESS  
H. POSITION  
V. POSITION  
FREQUENCY  
PHASE  
AUTO POSITION OVERRIDE  
LANGUAGE  
OSD SETTING  
COLOR TEMPERATURE  
ISM  
0
0
0
Brightness Menu  
100  
H. Position Menu  
100  
V. Position Menu  
100  
0
0
0
EDGE ENHANCEMENT  
DYNAMIC CONTRAST  
DEFAULT SETTING  
INFORMATION  
Frequency Menu  
100  
100  
Phase Menu  
Auto Position Menu  
DISABLE  
OSD H Position  
OSD V Position  
1024 X 768  
1280 X 768  
1360 X 768  
1366 X 768  
0
0
100  
Language Menu  
100  
ENGLISH  
ITALIAN  
FRENCH  
SPANISH  
GERMAN  
PORTUGUESE  
RUSSIAN  
CHINESE  
OSD Dwelling Time  
OFF  
5
30  
OSD Setting Menu  
OSD Setting Menu  
OSD H. POSITION  
OSD V. POSITION  
OSD DISPLAY TIME  
SETUP  
R-Gain Menu  
G-Gain Menu  
B-Gain Menu  
Reset Setting  
0
0
0
100  
100  
100  
Color Temperature Menu  
NORMAL  
COOL  
User Menu  
R-GAIN  
G-GAIN  
B-GAIN  
RESET  
USER  
ISM Menu  
ON OFF  
1
8
Edge Enhancement Menu  
OFF  
ON  
RESTORE  
Dynamic Contrast Menu  
OFF  
ON  
Default Setting Menu  
RESTORE  
INFORMATION  
Figure 10. RGB and DVI Mode Menu  
18  
C2927M-D (9/09)  
 
   
Not all menus are available for both RGB and DVI. Menus that are unavailable do not appear dimmed, while some menus that do not apply are  
not shown.  
The RGB and DVI mode menu contains the following features:  
Input: Changes the video input option. Select RGB or DVI.  
Contrast: Adjusts the black level of the image (0 to 100).  
Brightness: Adjusts the white level of the image (0 to 100).  
H-Position: (RGB only; dimmed in DVI mode.) Adjusts the horizontal position (0 to 100).  
V-Position: (RGB only; dimmed in DVI mode.) Adjusts the vertical position (0 to 100).  
Frequency: (RGB only; dimmed in DVI mode.) Adjusts the horizontal size of the screen image (0 to 100).  
Phase: (RGB only; dimmed in DVI mode.) Adjusts image distortion appearing as horizontal noise on the screen (0 to 100).  
Auto Position Override: Changes the display resolution. Select DISABLE, 1024 x 768, 1280 x 768, 1360 x 768, or 1366 x 768.  
This menu is enabled only when one of the listed resolution settings is selected.  
If an input signal causes problems on the screen, select a different setting.  
The Auto Position menu has no effect on resolution inputs that are not listed.  
Language: Changes the language selection. Select English, Italian, French, Spanish, German, Portuguese-Brazilian, Russian, or Chinese for the  
OSD display.  
OSD Setting: Select SETUP for the on-screen display. Then select one of the following:  
OSD H.POSITION: Adjusts the OSD horizontal position (0 to 100).  
OSD V.POSITION: Adjusts the OSD vertical position (0 to 100).  
OSD DISPLAY TIME: Adjusts the display time (OFF or 5 to 30 seconds). Selecting 5 or 30 determines how many seconds the display  
remains on the screen after you press a button. Selecting OFF means no delay.  
Color Temperature: Select NORMAL, COOL, or USER. NORMAL is the regular color level while COOL decreases the color level. If you select  
USER, then select from the following:  
R-Gain: Adjusts gain for red (0 to 100).  
G-Gain: Adjusts gain for green (0 to 100).  
B-Gain: Adjusts gain for blue (0 to 100).  
Reset: Select RESTORE to return to the original color temperature settings.  
(Image sticking minimization): Sets the recovery time of an LCD panel display when screen burn-in occurs (when a fixed image has been  
displayed for a long time). The ISM function starts working after the power is off for 10 minutes. Select ON, OFF, or from 1 to 8 hours for the  
operation period.  
Edge Enhancement: Improves the edge characteristic. The default setting is OFF.  
Dynamic Contrast: Improves the contrast characteristic. The default setting is ON.  
Default Setting: Select RESTORE to reset the monitor to the default settings.  
Information: Select INFORMATION to access Pelco headquarters information.  
C2927M-D (9/09)  
19  
 
Troubleshooting  
If the following instructions fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or +1-559-292-1981  
(international) for assistance. Be sure to have the serial number available when calling.  
Do not try to repair the unit yourself. Opening it immediately voids the warranty. Leave maintenance and repairs to qualified technical personnel  
only. Refer to the Product Warranty and Return Information located on the inside back page of this document.  
WARNING: To reduce the risk of electrical shock, do not remove the cover or back of the monitor. There are no user-serviceable parts are  
inside.  
Table A. Troubleshooting the PMCL400 Series Monitor  
Problem  
Possible Cause  
Suggested Resolution  
Poor picture quality Faulty system or cable connections. Make adjustments on the front panel control.  
Inspect all system connections and cables.  
Maintenance  
Periodically, you might need to clean the PMCL400 Series monitor to maintain optimum viewing performance. Be sure to observe the following  
cleaning instructions to avoid damage to the monitor:  
Gently wipe your screen with a clean camel-hair brush or a soft, clean, lint-free cloth.  
Gently apply pressure to the screen surface to clean the display.  
Do not spray any liquid directly on the screen or the LCD monitor casing. Chemical cleaners can damage the screen and the LCD monitor  
casing.  
20  
C2927M-D (9/09)  
 
     
Specifications  
GENERAL  
Viewing Area  
PMCL417A  
PMCL419A  
338 x 270 mm  
376 x 301 mm  
Pixel Pitch  
PMCL417A  
PMCL419A  
0.264 x 0.264 mm  
0.294 x 0.294 mm  
450 cdm2  
Brightness  
Contrast Ratio  
Backlight Type  
Viewing Angle (H/V)  
Response Time  
Native Resolution  
Panel Aspect Ratio  
Panel Life  
800:1  
4 CCFL  
160°/160°  
5 ms  
1280 x 1024 SXGA  
5:4  
50,000 hours  
Display Colors  
Front Panel Controls  
Indicators  
16.7 million  
Power, source/enter, menu/exit, up/down, vol +/-  
LED, power on/off  
ELECTRICAL  
Power Consumption  
50 W  
Input Voltage  
100 to 240 VAC, 50/60 Hz  
Input Interfaces  
Video  
Audio  
2 BNC, looping; 1 S-Video, looping; 1 RGB; 1 DVI  
2 RCA jack, looping; 1 PC  
Horizontal Frequency  
Vertical Frequency  
Sync Format  
31 kHz to 80 kHz  
56 Hz to 75 Hz  
NTSC/PAL  
ENVIRONMENTAL  
Operating Temperature  
32° to 104°F (0° to 40°C)  
-4° to 140°F (° to 60°C)  
Storage Temperature  
Operating Humidity  
Storage Humidity  
20% to 80%, noncondensing  
10% to 90%, noncondensing  
PHYSICAL  
Dimensions  
PMCL417A  
PMCL419A  
2.4" D x 14.9" W x 13.4" H (6.1 x 37.8 x 34.1 cm)  
2.4" D x 16.4" W x 14.5" (6.1 x 41.5 x 36.9 cm)  
Unit Weight  
PMCL417A  
PMCL419A  
10.8 lb (4.9 kg)  
12.6 lb (5.7 kg)  
Shipping Weight  
PMCL417A  
PMCL419A  
16 lb (7 kg)  
18 lb (8 kg)  
(Design and product specifications subject to change without notice.)  
C2927M-D (9/09)  
21  
 
 
Appendix  
RGB/DVI MODE SUPPORTED FREQUENCIES  
Table B describes the resolution supported under different frequencies.  
NOTE: Not all resolutions generated by your video source are available on the monitor.  
Table B. RGB and DVI Mode Supported Frequencies  
Vertical  
Mode Resolution  
Frequency (Hz)  
720 X 400  
640 x 480  
800 x 600  
1024 x 768  
70  
60/72/75  
56/60/72/75  
60/70/75  
60/75  
VGA  
SVGA  
XGA  
SXGA 1280 x 1024  
WXGA 1280 x 720  
WXGA 1140 x 900  
60  
60  
22  
C2927M-D (9/09)  
 
     
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to a Pelco designated location. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Exceptions to this warranty are as noted below:  
• Five years:  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelcos liability  
for any claim, whether based on breach of contract, negligence, infringement of  
any rights of any party or product liability, relating to the Products shall not exceed  
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be  
liable for any special, incidental, or consequential damages (including loss of use,  
loss of profit, and claims of third parties) however caused, whether by the  
negligence of Pelco or otherwise.  
Fiber optic products  
TW3000 Series unshielded twisted pair (UTP) transmission products  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models  
• Three years:  
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,  
C10CH Series, IP3701H Series, and IX Series)  
EH1500 Series enclosures  
Spectra® IV products (including Spectra IV IP)  
Camclosure® Series (IS, ICS, IP) integrated camera systems  
The above warranty provides the Dealer with specific legal rights. The Dealer may  
also have additional rights, which are subject to variation from state to state.  
DX Series digital video recorders, DVR5100 Series digital video recorders,  
Digital Sentry® Series hardware products, DVX Series digital video  
recorders, and NVR300 Series network video recorders  
Endura® Series distributed network-based video products  
Genex® Series products (multiplexers, server, and keyboard)  
PMCL200/300/400 Series LCD monitors  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the  
following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number  
3. Details of the defect or problem  
• Two years:  
If there is a dispute regarding the warranty of a product that does not fall under  
the warranty conditions stated above, please include a written explanation with  
the product when returned.  
Standard varifocal, fixed focal, and motorized zoom lenses  
DF5/DF8 Series fixed dome products  
Legacy® Series integrated positioning systems  
Spectra III, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20  
scanners, including when used in continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which the  
item was received by Pelco.  
Esprit Ti and TI2500 Series thermal imaging products  
Esprit and WW5700 Series window wiper (excluding wiper blades).  
CM6700/CM6800/CM9700 Series matrix  
RETURNS  
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100  
or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair) and designated return location.  
Digital Light Processing (DLP®) displays (except lamp and color wheel). The  
lamp and color wheel will be covered for a period of 90 days. The air filter is  
not covered under warranty.  
Intelli-M® eIDC controllers  
PMCL542F, PMCL547F, and PMCL552F FHD monitors  
All merchandise returned for credit may be subject to a 20 percent restocking and  
refurbishing charge.  
• One year:  
Video cassette recorders (VCRs), except video heads. Video heads will be  
covered for a period of six months.  
• Six months:  
All pan and tilts, scanners, or preset lenses used in continuous motion  
applications (preset scan, tour, and auto scan modes).  
Goods returned for repair or credit should be clearly identified with the assigned  
CA or RA number and freight should be prepaid.  
8-13-09  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
C2927M  
C2927M-A  
Date  
01/06  
01/06  
Comments  
Original version.  
Changed diagonal screen size to 381 mm for the PMCL415 and to 432 mm for the PMCL417. Changed the backlight type to 4 CCFL for the PMCL419. Changed the  
power consumption to <60W for the PMCL417 and PMCL419. Removed the standby mode specification. Also, removed the second occurrence of the tilt angle  
specification.  
C2927M-B  
C2927M-C  
C2927M-D  
8/06  
12/06  
9/09  
In the Specifications section, changed the PMCL419 response time to 8 ms.  
Changed PMCL417 response time to 8 ms.  
Revised manual to include information for all new models: PMCL417A and PMCL419A..  
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.  
Spectra III is a trademark of Pelco, Inc.  
© Copyright 2009, Pelco, Inc. All rights reserved.  
DLP is a registered trademark of Texas Instruments Incorporated.  
All product names and services identified throughout this document are trademarks or registered trademarks of their respective companies.  
The absence of a trademark or registered trademark from this document does not constitute a waiver of intellectual property rights.  
 
Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA  
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150  
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120  
 

Philips CD Player 313 User Manual
Philips CRT Television 170X4 User Manual
Philips Headphones HC 8391 User Manual
Philips Hearing Aid ZA312B6A User Manual
Philips Surge Protector SPP2302WC User Manual
Philips TV VCR Combo 14 PV 274 User Manual
Pioneer CD Player DEH 2800MP User Manual
Porter Cable Drill 23 8300 56 User Manual
Porter Cable Paint Sprayer PSH2 User Manual
PVI Industries Water Heater PV 19A User Manual