Pelco Computer Hardware C1501M A User Manual

CM9700-CC1-VID  
VGA Video Card  
C1501M-A (3/05)  
I N S T A L L A T I O N  
 
Regulatory Notices  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However there is no guarantee that the  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve  
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,  
Washington D.C. 20402.  
Changes and modifications not expressly approved by the manufacturer or registrant of this  
equipment can void your authority to operate this equipment under Federal Communications  
Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
C1501M-A (3/05)  
 
3
4
C1501M-A (3/05)  
 
Installation Instructions for CM9700-CC1-VID  
1. Turn off all power to the CC1. Disconnect and label all attached cabling.  
WARNINGS:  
Failure to turn off the CC1 power could result in serious damage to the equipment.  
Electrostatic Discharge (ESD) precautions must be observed when performing the  
procedures described in this manual. Always wear a gounding strap connected to an  
approved grounding source when working on or around exposed electronic components.  
2. Install the VGA card in the CC1. Refer to Figures 1 and 2 and do the following:  
a. Loosen and remove the top cover mounting screws.  
b. From the rear, tilt the top cover up at a slight angle, and then pull backwards away from  
the front edge to remove it from the CC1 chassis.  
c.  
Remove the retaining screw of the existing graphics card. Gently pull the card straight  
up. If there is no existing card, remove the retaining screw for the slot cover of any  
vacant PCI expansion slot. Slide the cover out.  
d. Install the new VGA card into the selected PCI expansion slot from step c. Carefully align  
the gold-fingered edge connector of the VGA card with the PCI slot. Gently but firmly  
press the VGA card down until fully seated into the PCI slot. Reinstall the retaining  
screw to secure the VGA card into place.  
e. Reinstall the top cover and secure with mounting screws.  
Figure 1. Removing the CC1 Top Cover  
C1501M-A (3/05)  
 
5
RETAINING  
SCREW  
SLOT  
COVER  
1
2
3
4
ISA  
PCI  
SLOTS  
EXPANSION  
SLOTS  
Figure 2. CC1 Internal Layout  
UTILITY DISK SOFTWARE INSTALLATION  
1. If not done after installation of the VGA card, reconnect all cabling to the CC1.  
NOTE: A keyboard and monitor must be connected to the CC1 in order to install the driver software.  
2. Apply power to the CC1.  
3. Insert the driver utility disk into the “A” drive of the CC1.  
4. When “C:\9700>” appears on the screen, type the following:  
a:\install  
NOTE: If your system is in the A directory, “A:\>” will appear. In this case, type install only.  
5. Press the Enter key.  
6. The drivers and where they will be installed will be displayed on the screen. The option of  
either aborting or continuing the installation will be given.  
To abort installation, press the CTRL+C keys. The files will not be installed.  
To continue installation, press any key on the keyboard. The files will be installed.  
7. Upon completion, “Installation successful” will appear on the screen.  
8. Remove the utility disk from the “A” drive and press CTRL+ALT+DEL to reboot the system.  
6
C1501M-A (3/05)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of  
shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
CC3651H-2X camera models, which have a five-year warranty.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 Scanners, including when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and EnduraSeries distributed network-based video  
products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight  
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this  
warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s  
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products  
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state  
to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and  
provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization  
number (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate  
address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the  
following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
REVISION HISTORY  
Manual #  
C1501M  
C1501M-A  
Date Comments  
9/99 Original version.  
3/05 Changed part number to reflect VGA-only output per ECO 04-10632.  
Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, and Camclosure are registered trademarks of Pelco.  
©Copyright 2005, Pelco. All rights reserved.  
 
®
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Peavey Music Pedal Dirty Dog User Manual
Philips Cell Phone SE735 User Manual
Philips Clock Radio AJT600 37 User Manual
Philips Computer Monitor 104S19 User Manual
Philips MP3 Player AJ3230 User Manual
Planet Technology Telephone VIP 255PT User Manual
Polk Audio Speaker MM840SVC User Manual
Poulan Trimmer 545177326 User Manual
Powermate Portable Generator PM0101400 User Manual
Preh Computer Monitor MCI 15 User Manual