Pelco Computer Monitor C1909M User Manual

®
PMC9A  
High-Resolution Color  
Monitor  
Installation/  
Operation Manual  
C1909M (4/01)  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150  
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Operate this unit only from the type of power source indicated on the label.  
2. Do not block or cover ventilation openings on the back or bottom of the monitor  
cabinet.  
3. Do not place this monitor near a radiator or heating vent.  
4. Do not push objects of any kind through cabinet openings. This may result in fire or  
electrical shock.  
5. Before adding attachments always ask a service technician to perform routine safety  
tests to determine that equipment is in safe operating condition. Ground potential tests  
should be part of the routine safety check made by the service technician.  
6. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure  
personnel or damage equipment.  
7. Route power cords so that they cannot be walked upon or tripped over. Do not allow  
anything to rest on the power cord.  
8. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not  
spill liquid of any kind on the unit.  
9. Unplug the power cord from the unit before cleaning the display. Use only a damp  
cloth. Do not use alcohol, spirits, or ammonia to clean the display. DO NOT AT-  
TEMPT TO CLEAN THE INTERIOR OF THIS UNIT-THIS ACTION MUST  
BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED DUR-  
ING NORMAL MAINTENANCE.  
10. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER  
BY UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DAN-  
GEROUS VOLTAGES OR OTHER HAZARDS.  
11. Unplug the unit immediately and notify the service technician.  
A. If liquid has been spilled into the display or the display has been exposed to rain  
or water.  
B. If the unit has been dropped or the cabinet damaged.  
C. If fuses continue to blow.  
D. If the power cord is damaged or frayed.  
E. If a distinct change from normal operation is apparent.  
12. A CCC-approved power cord must be used to power this equipment when used in  
China.  
When replacement parts are required, be sure that the service technician uses components  
specified by the manufacturer which have the same characteristics as the original parts.  
UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL  
SHOCK OR OTHER HAZARDS.  
Upon completion of any service or repairs, ask the technician to perform safety checks to  
determine that the equipment is in safe operating condition.  
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS  
OF THIS MONITOR. DO NOT OPEN THE COVERS UNDER ANY CIRCUM-  
STANCES, THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous volt-  
age constituting a risk of electric shock is  
present within this unit.  
C A U T I O N :  
RISK OF ELECTRIC SHOCK.  
This symbol indicates that there are impor-  
tant operating and maintenance instructions  
in the literature accompanying this unit.  
DO NOT OPEN.  
Please thoroughly familiarize yourself with the information in this manual prior to installation  
and operation.  
Pelco Manual C1909M (4/01)  
3
 
DESCRIPTION  
The PMC9A is a high-resolution, 9-inch (23 cm) color monitor. The unit has a resolution of  
300 TV lines producing an excellent-quality picture. The monitor’s power input of 100-240  
VAC, 50/60 Hz, is automatically detected upon power up. All image adjustment controls are  
conveniently located on the front panel of the monitor.  
INSTALLATION  
The monitor may be placed on any flat surface (desk or  
table) or rack-mounted. To rack-mount the monitor follow the  
instructions supplied with the rack-mount kit.  
1. Video Cable Connection (refer to Table A).  
IN  
a. Connect the video cable to the BNC video input  
labeled VIDEO A IN on the back panel of the  
monitor. If the installation requires a second video  
input, connect a video cable to the BNC video  
input labeled VIDEO B IN.  
VIDEO A  
OUT  
IN  
VIDEO B  
OUT  
NOTE: If using S-Video  
connect the video cable to  
the input labeled S-VHS IN.  
b. Looping Operation Only – Connect a video cable  
to the BNC connector labeled VIDEO A OUT. If the  
installation requires a second video output,  
S-VHS IN  
connect a video cable to the BNC video output  
labeled VIDEO B OUT. Refer to Figures 2 and 3.  
IN  
OUT  
2. Plug the power cord (provided) into the AC INLET con-  
nection on the back panel. Plug the other end of the  
cord into a power receptacle.  
AUDIO AUDIO  
2
1
00595  
Figure 1. Back Panel Layout  
4
Pelco Manual C1909M (4/01)  
 
Table A. Video Coaxial Cable Requirements  
Cable Type*  
RG59/U  
RG6/U  
Maximum Distance  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
*Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95%braid coverage  
IN  
VIDEO A  
OUT  
CAMERA  
VCR  
IN  
VIDEO B  
CAMERA  
OUT  
VCR  
S-VHS IN  
IN  
OUT  
AUDIO AUDIO  
2
1
00598  
Figure 2. Looping Operation – One Monitor with External Video Equipment  
IN  
IN  
IN  
VIDEO A  
VIDEO A  
VIDEO A  
OUT  
OUT  
OUT  
CAMERA  
IN  
IN  
IN  
VCR  
VIDEO  
OUT  
B
VIDEO  
OUT  
B
VIDEO  
OUT  
B
S-VHS IN  
S-VHS IN  
S-VHS IN  
IN  
IN  
IN  
OUT  
OUT  
OUT  
AUDIO  
2
AUDIO AUDIO  
AUDIO AUDIO  
AUDIO  
1
2
1
2
1
00597  
Figure 3. Looping Operation – Maximum of Three Monitors with  
External Video Equipment  
Pelco Manual C1909M (4/01)  
5
 
OPERATION  
1. Turn the monitor ON. Wait 30 seconds for the picture tube to warm up and the power  
LED indicator to light.  
2. Select the video source (V1, V2, S-VHS) using the VIDEO selection button located on  
the front panel of the monitor.  
3. If required adjust the picture using the control knobs on the front panel.  
FRONT PANEL ADJUSTMENTS  
SHARP  
TINT  
Adjust the control to obtain the clearest picture.  
Turn the control clockwise to increase the greenish tones in the picture.  
Turn the control counterclockwise to increase the reddish tones in the pic-  
ture.  
COLOR  
Turn the control clockwise to increase the saturation level and counterclock-  
wise to decrease the saturation level.  
BRIGHT  
Turn the control clockwise to increase brightness and counterclockwise to  
decrease brightness.  
CONTRAST Proper adjustment will allow maximum gradations between the darkest and  
lightest picture contrast. Turn the control clockwise to increase picture con-  
trast and counterclockwise to decrease contrast.  
VOLUME  
Turn the control clockwise to increase volume and counterclockwise to de-  
crease volume.  
V1 V2 S-VHS  
VIDEO  
SHARP  
TINT  
COLOR BRIGHT CONTRAST VOLUME  
POWER  
00596  
Figure 4. Front Panel Controls  
MAINTENANCE  
If the quality of the picture is poor and cannot be improved by making adjustments on the  
front control panel, inspect all system connections and cable runs.  
To reduce the risk of electrical shock, do not remove the cover or the back. No user-  
serviceable parts are inside. Refer servicing to qualified personnel, or contact the Pelco  
Customer Service Department for assistance. Refer to the Warranty and Return Information  
section.  
6
Pelco Manual C1909M (4/01)  
 
SPECIFICATIONS  
ELECTRICAL  
Input Voltage:  
100-240 VAC, 50/60 Hz, automatic switching  
45 watts  
Power Consumption:  
Horizontal Resolution: 300 TV lines  
Visual Picture Size:  
Sweep Linearity:  
Speaker Output:  
GENERAL  
9-inch (23 cm) diagonal  
10%  
1.0 watt (-3 dBV)  
Input/Output  
Video:  
2 BNC inputs, 75 ohms or Hi-Z  
2 looping outputs  
Audio:  
2 RCA input, Hi-Z  
2 looping output  
S-Video:  
Construction:  
Finish:  
1 DIN input  
Steel cabinet  
Black  
Dimensions:  
8.66 (W) x 8.76 (H) x 12.48 (D) inches  
(22 x 22.3 x 31.7 cm)  
Weight:  
15.4 lb (7 kg)  
ENVIRONMENTAL  
Operating Temperature: 32° to 106°F (0° to 41°C)  
Humidity: 0% to 90% (non-condensing)  
(Design and product specifications subject to change without notice.)  
This equipment contains electrical or electronic components that must be  
recycled properly to comply with Directive 2002/96/EC of the European  
Union regarding the disposal of waste electrical and electronic equipment  
(WEEE). Contact your local dealer for procedures for recycling this  
equipment.  
Pelco Manual C1909M (4/01)  
7
 
REGULATORY NOTICES  
This equipment has been tested and found to comply with the limits of a Class B digital de-  
vice, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment gener-  
ates, uses, and can radiate radio frequency energy and, if not installed and used in accor-  
dance with the instructions, may cause harmful interference to radio communications. How-  
ever there is no guarantee that the interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception, which can  
be determined by turning the equipment off and on, the user is encouraged to try and cor-  
rect the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the re-  
ceiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual # Date  
C1909M 4/01  
Comments  
Original version.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
© Copyright 2001, Pelco  
All rights reserved.  
8
Pelco Manual C1909M (4/01)  
 

Peavey Speaker System PR 1000 User Manual
Peerless Industries Projector Accessories PAP 121 User Manual
Pelco Home Security System CM100 User Manual
Philips Baby Accessories SCF276 33 User Manual
Philips Universal Remote TSU9600 User Manual
Pioneer CD Player DEH 1300MP User Manual
Poulan Snow Blower 183615 User Manual
Praktica Digital Camera D00390 User Manual
Pride Mobility Mobility Aid commander 400 User Manual
Pride Mobility Mobility Aid Jazzy 600 2S User Manual