Pelco DVR C2619M User Manual

DVR5100 Series  
System Software  
Recovery Instructions  
C2619M (8/06)  
 
Recovering the Administrator Password  
Follow these instructions to reset the password for the default administrator user. These instructions change the password for the default user  
called admin. No other passwords are reset. If you want to reset system configuration or delete recorded video at the same time, choose one of  
the other functions from the main screen.  
1. Follow the instructions at Working with the Recovery Disc on page 2 to set up a temporary primary monitor. The main screen appears.  
Figure 2. DVR5100 Recovery Disc Main Screen  
2. Select Recover Administrator Password by pressing the blue function key  
. A message appears asking you to confirm that you want  
to reset the password.  
3. Press the blue function key  
to continue, or press the yellow function key to stop the procedure and return to the main screen.  
The password for the default user called admin is reset to its original factory setting. The default password is admin, which is the  
equivalent to 23646 on the keypad. If this user was deleted, it is recreated and assigned the default password. A progress message  
appears on the screen followed by a message stating that the password has been changed.  
After the password has been reset, the recovery disc is ejected and the DVR5100 restarts automatically.  
4. If the password has not been reset, repeat the procedure.  
C2619M (8/06)  
3
 
 
Resetting System Configuration to Factory Defaults  
Follow these instructions if you want to reset all system configuration settings to their original factory defaults. This includes resetting the  
passwords for all default user accounts. For a list of original default settings, refer to the installation manual. If you also want to delete video,  
refer to Resetting System Configuration and Deleting Recorded Video on page 9. If you want to reset only the default user password, refer to  
WARNING: Interrupting this configuration process while it is in progress might cause damage to the system that can make the unit  
inoperable. Do not remove the DVD until you are instructed to do so.  
1. Follow the instructions at Working with the Recovery Disc on page 2 to set up a temporary primary monitor. The main screen appears.  
Figure 3. DVR5100 Recovery Disc Main Screen  
2. Select Reset System Configuration by pressing the yellow function key  
reset all system configuration settings to their original factory defaults.  
. A message appears that warns you that you are about to  
Figure 4. Warning Message: Resetting System Configuration  
4
C2619M (8/06)  
 
3. Press the blue function key  
to continue, or press the yellow function key  
to stop the procedure and return to the main screen.  
If you choose to continue the procedure, the following message appears on the screen while the system configuration settings are reset to  
their factory default settings. Resetting system configuration information can take several minutes and varies from model to model.  
Figure 5. Progress Message: Resetting System Configuration  
After the system has completed resetting all configuration settings, the following message appears.  
Figure 6. Completion Message: Resetting System Configuration  
After the system configuration settings have been reset, the recovery disc is ejected and the DVR5100 restarts automatically.  
4. If settings have not been reset, repeat the procedure.  
C2619M (8/06)  
5
 
Deleting Recorded Video  
Follow these procedures if you want to delete all recorded video that is currently stored on the hard disk or hard disks in the DVR5100. If you also  
want to reset system configuration information, refer to Resetting System Configuration and Deleting Recorded Video on page 9.  
WARNING: This procedure deletes all recorded video from the hard disks. You cannot recover any previously recorded video after this  
procedure is completed. If you have critical video on the unit that you must retrieve, contact your system administrator or a Pelco technical  
support representative before running the procedure for alternate instructions. Refer to Introduction on page 2 if you need to change only a  
portion of these settings.  
Interrupting this process while it is progress might cause damage to the system that can make the unit inoperable. Do not remove the DVD  
until you are instructed to do so.  
1. Follow the instructions at Working with the Recovery Disc on page 2 to set up a temporary primary monitor. The main screen appears.  
Figure 7. DVR5100 Recovery Disc Main Screen  
2. Select Delete Recorded Video by pressing the green function key  
recorded video.  
. A message appears that warns you that you are about to delete  
6
C2619M (8/06)  
 
Figure 8. DVR5100 Confirmation Message: Deleting Recorded Video  
3. Press the blue function key  
to continue, or press the yellow function key  
to stop the procedure and return to the main screen.  
If you choose to continue the procedure, the following message appears on the screen while the system deletes all recorded video.  
Figure 9. Progress Message: Deleting Recorded Video  
C2619M (8/06)  
7
 
After the system has completed deleting all recorded video, the following message appears.  
Figure 10. Completion Message: Deleting Recorded Video  
After the recorded video has been deleted, the recovery disc is ejected and the DVR5100 restarts automatically.  
4. If recorded video was not deleted, repeat the procedure.  
8
C2619M (8/06)  
 
Resetting System Configuration and Deleting Recorded Video  
Follow these procedures if you want to reset the system configuration to the factory defaults and delete all recorded video that is currently  
stored on the hard disk or hard disks in the DVR5100.  
WARNING: This procedure resets the admin user password, resets all system configuration settings, and deletes all recorded video from  
the hard disks. You cannot recover any previously recorded video after this procedure is completed. If you have critical video on the unit that  
you must retrieve, contact your system administrator or a Pelco technical support representative before running the procedure for alternate  
instructions. Refer to Introduction on page 2 if you need to change only a portion of these settings.  
Interrupting this process while it is progress might cause damage to the system that can make the unit inoperable. Do not remove the DVD  
until you are instructed to do so.  
1. Follow the instructions at Working with the Recovery Disc on page 2 to set up a temporary primary monitor. The main screen appears.  
Figure 11. DVR5100 Recovery Disc Main Screen  
2. Select Reset Configuration and Delete Recorded Video by pressing the red function key  
are about to reset configuration settings and delete recorded video.  
. A message appears that warns you that you  
C2619M (8/06)  
9
 
 
Figure 12. Confirmation Message: Resetting System Configuration and Deleting Recorded Video  
3. Press the blue function key  
to continue, or press the yellow function key  
to stop the procedure and return to the main screen.  
If you choose to continue the procedure, the following message appears on the screen while the system deletes all recorded video.  
Resetting system configuration information can take several minutes and varies from model to model.  
Figure 13. Progress Message: Resetting System Configuration and Deleting Recorded Video  
10  
C2619M (8/06)  
 
After the system has completed resetting system configuration and deleting all recorded video, the following message appears.  
Figure 14. Completion Message: Resetting System Configuration and Deleting Video  
After the procedure has completed, the recovery disc is ejected and the DVR5100 restarts automatically.  
4. If the procedure was unsuccessful, repeat the procedure.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
REVISION HISTORY  
Manual #  
Date  
Comments  
C2619M  
8/06  
Original version.  
Pelco and the Pelco logo are registered trademarks of Pelco.  
Endura is a trademark of Pelco.  
©Copyright 2006, Pelco. All rights reserved.  
C2619M (8/06)  
11  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Pentax Digital Camera ZOOM70 X User Manual
Philips Baby Monitor 9VD200 User Manual
Philips CD Player SA018102 User Manual
Philips Speaker SBC BC280 User Manual
Planar Digital Camera 020 1229 00A User Manual
Polar Exercise Bike CS200 User Manual
Polaris Automobile Sportsman 400 HO User Manual
Polaroid Flat Panel Television FLM 3232 User Manual
Poulan Lawn Mower Accessory 183187 User Manual
ProForm Treadmill 831295062 User Manual