Pelco DVR C664M B User Manual

I N S T A L L A T I O N M A N U A L  
DX7000 Series  
Digital Video Recorder  
®
C664M-B (8/02)  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use  
only and it must not be installed where exposed to rain and moisture.  
3. Only use replacement parts recommended by Pelco.  
4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and  
exposed parts to verify the exposed parts have not been connected to line circuitry.  
5. For USA and Canada, use only a UL listed CSA labeled detachable power cord, 3-conductor, 18 AWG, SVT, or SJT type,  
round type plug, parallel blade, cord connector body IEC 320 style to mate with inlet on product.  
6. To reduce the risk of fire, use only No. 2 AWG or larger telecommunications line cord.  
IMPORTANT: The only way to disconnect power completely is to unplug the power cord. Make sure at least one end of the  
power cord is within easy reach so that the unit can be unplugged when required.  
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR  
EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE  
MANUFACTURER’S INSTRUCTIONS.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of  
electric shock is present within this unit.  
C A U T I O N :  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important operating and  
maintenance instructions in the literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.  
WARNING  
This product is factory set to operate on 115 VAC.  
For 230 VAC operation, move the switch to the 230 VAC  
position before applying power to the unit.  
01204  
C664M-B (8/02)  
3
 
WELCOME  
Thank you for purchasing Pelco’s DX7000 Series, high-quality digital video recorder (DVR). Your new system combines the  
functions of a recorder and multiplexer into a product with versatile recording and playback functions.  
The following equipment is supplied with the DX7000 Series DVR:  
Qty  
Description  
1
1
1
1
2
2
1
1
6
2
4
1
1
Keyboard  
Mouse  
RS-422 communication converter, including power adapter  
9-pin to 25-pin adapter  
Power cables (1 USA standard and 1 European standard)  
Keys for front panel  
Microsoft Windows® 98 CD  
DX7000 Remote Site Software CD  
10-32 x .75-inch black mounting screws and washers  
Rack Mount ears, handles, and hardware (assembly required)  
Rubber feet  
Installation manual  
Operation/Programming manual  
NOTE: An uninterruptible power supply (UPS) is not supplied with the DVR. If required, Pelco recommends a device with the  
following specifications:  
Capacity – 350 VA, 210 watts  
Output voltage – 115V ±8% (on battery)  
Frequency range – 47 Hz to 63 Hz  
4
C664M-B (8/02)  
 
MOUNTING  
The DX7000 may be placed on a flat surface, such as a shelf, or it can be installed in a 19-inch (48.26 cm) equipment rack.  
FLAT SURFACE MOUNTING  
Before placing the unit on a flat surface, attach the rubber feet (supplied) to the bottom of the DVR. The unit may scratch the  
surface if the rubber feet are not installed.  
EQUIPMENT RACK MOUNTING  
To install the unit in an equipment rack:  
1. Attach the handles to the rack ears using four of the Phillips flat head screws (provided). Refer to Figure 1.  
2. Remove the top screw and bottom screw from the left and right side of the DVR. Remove the side plates. Refer to Figure 1.  
3. Use the screws removed from the sides of the DVR and attach the rack ears to the unit. Refer to Figure 1.  
4. Use four of the supplied 10-32 x .75-inch black screws and finishing washers and mount the assembly to a 19-inch (48.26 cm)  
rack or console. Installation of the assembly may require two persons. Pelco recommends 1RU spacing between units.  
REMOVE  
PLATE  
INSTALL  
RACK  
EAR  
Figure 1. Rack Ear Installation  
IMPORTANT: Slots and openings in the cabinet provide ventilation and prevent it from overheating. Do not block these  
openings. Never place the DVR near or over a radiator or heat register. Do not place it in a built-in installation, such as a rack,  
unless proper ventilation is provided or Pelcos instructions have been followed.  
C664M-B (8/02)  
5
 
BACK PANEL LAYOUT  
1
CAM1  
CAM2  
CAM8  
CAM14  
CAM3  
CAM9  
CAM15  
CAM4  
CAM10  
CAM16  
CAM5  
CAM6  
CAM7  
CAM11  
CAM12  
3
CAM13  
VIDEO  
SENSOR  
RELAY  
OUTPUT  
1
2
3
4
5
6
7
8
COM  
1
2
3
4
5
6
7
8
COM  
NTSC  
NTSC  
PAL  
5
2
4
PAL  
7
ACT LINK  
18  
8
16  
15  
12  
13  
Audio  
L-IN  
1
2
L-OUT  
MIC  
1
2
6
19  
17  
11 10 9  
14  
Figure 2. Back Panel Layout  
1
2
3
4
5
6
7
8
9
Camera Inputs – 8 or 16 BNC camera inputs  
Alarm Inputs – 8 normally closed dry contact inputs  
Analog Monitor Output – One BNC output (sequencing only)  
Relay Outputs – 8 normally open dry contact outputs  
VGA Monitor Output – 15-pin output  
Ethernet Adapter Port – 10/100 port  
NTSC/PAL Selection Switches  
Joystick Port (Not used)  
Microphone Jack (Not used)  
10 Audio IN/OUT (Not used)  
11 COM 2 Serial Port – 9-pin port  
12 LPT1 Printer Port – 25-pin port  
13 COM 1 Serial Port – 9-pin port  
14 USB Ports – For Pelco-supported devices only  
15 Keyboard (PS/2) Input  
16 Mouse (PS/2) Input  
17 AC Power Output  
18 Power Voltage Selection Switch – This product is set at the factory to operate on 115 VAC. For 230 VAC operation, move  
the switch to the 230 VAC position before applying power to the unit.  
19 AC Power Input – Please see Important Safeguards and Warnings.  
6
C664M-B (8/02)  
 
BASIC INSTALLATION  
Basic installation covers all the equipment necessary to program and operate the system. Refer to the Extended Installation  
section for PTZ, alarm, sensors, and network connections.  
Verify that the  
voltage is set  
correctly for  
your location  
a
r
e
m
a
C
D C C r o l  
o
C
P S D S P C o l o r C C D C a m e r a  
7
115  
OR  
230  
6
NTSC  
PAL  
1
2
5
4
3
Figure 3. Basic Equipment Installation  
1
Set the Voltage Selection Switch - Verify that the voltage selection switch is set correctly for your location. This product  
is set at the factory to operate on 115 VAC. For 230 VAC operation, move the switch to the 230 VAC position before  
applying power to the unit.  
2
3
4
5
6
7
Connect the power cord to the AC input located on the back panel. Plug the other end of the power cord into an AC outlet.  
Connect the keyboard to the bottom PS/2 input.  
Connect the mouse to the top PS/2 input.  
Set the NTSC/PAL switches to the correct camera setting for your location.  
Connect the VGA monitor (not supplied).  
Connect the cameras. Refer to the following table for video coaxial cable requirements:  
Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
RG11/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
* Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid  
coverage  
C664M-B (8/02)  
7
 
EXTENDED INSTALLATION  
Extended installation covers installation of accessories for the DX7000. Refer to the Basic Installation section to install the  
basic equipment necessary to program and operate the system.  
5
4
Analog (spot) Monitor  
3
NOTE: A standard European  
plug is attached to the  
power adapter. To convert  
the adapter to the USA  
standard loosen the Phillips  
head screw and remove  
the European plug.  
Network  
2
1
Power  
Figure 4. Extended Equipment Installation  
1
PTZ (RS-422 Converter)  
To control receivers with pan/tilt and zoom functions, such as Pelcos Espritand Spectra® systems, you must install the  
RS-422 communication converter. The DX7000 DVR cannot operate PTZ receivers if the RS-422 converter is not installed  
and the PTZ receiver address is not set to accept D protocol control. For information on setting the receiver address for D-  
type control, refer to the documentation supplied with the PTZ receiver.  
Do the following to install the RS-422 converter:  
a. Connect the control wires from the receiver to the RS-422 converter (refer to Figure 5). The DX7000 can support up  
to 16 PTZ devices, at a maximum of 4,000 feet (1,219 m).  
b. Set the DTE/DCE switch located on the bottom of the converter to DCE (refer to Figure 6).  
c. Plug the RS-422 converter into the 9-pin to 25-pin adapter.  
d. Plug the pin converter into the COM 1 Port.  
e. Attach the power adapter to the RS-422 converter.  
f. Plug power adapter into a power source.  
NOTE: The DX7000 may  
be connected to Pelcos  
PTZ  
SERIES TERMINATE  
PTZ  
PTZ  
THE LAST PTZ IN  
CM9760-CXT-A for  
RXRXTX TX RXRXTX TX RXRXTX TX  
+
-
+
-
+
-
+
-
+
-
+
-
Coaxitron® control. Refer  
to the manual for the  
CM9760-CXT-A for  
installation instructions.  
SUPPORTS UP TO 16 PTZ  
MAXIMUM: 4,000 FEET (1,219M)  
Figure 5. PTZ Installation  
8
C664M-B (8/02)  
 
DTE  
DCE  
SET TO DCE  
DC 9V  
Connection  
A
T+  
T-  
R-  
R+  
B
+
R+  
R-  
T-  
T+  
T+T-R-R+  
Figure 6. Bottom View of the RS-422 Converter  
2
3
TCP/IP Access  
Consult your network administrator to avoid possible network conflicts. For TCP/IP access, connect the DX7000 to a  
10/100 Ethernet network. Use a standard UTP Cat5 cable with RJ-45 connectors. Plug the cable into the LAN port located  
on the back of the unit. Use a router with multi-casting when connecting to a WAN network.  
Analog Spot Monitor (Sequencing only)  
You can connect an analog monitor to the DX7000. This monitor is for viewing purposes only. Programming menus and  
bars are not displayed on the screen. All enabled cameras are displayed on the monitor in a sequential order.  
Connect the analog spot monitor to the output labeled VIDEO OUTPUT.  
4
5
Sensor (Alarm) Inputs  
The DX7000 has eight normally closed dry contact sensor inputs. Sensor inputs require an open circuit contact, such as a  
switch or relay, to trigger an alarm.  
To wire a sensor input:  
a. Connect one wire from the source device (for example, a door) to one of the sensor input terminals 1 through 8.  
b. Connect a second wire from the source device to the COM terminal.  
Relay Outputs (Maximum power rating 125 VAC, 0.5A; 30VDC, 1A)  
The DX7000 has eight normally opened dry contact relay outputs. A signal from a output will operate the device  
connected to the output.  
To wire a relay output:  
a. Connect one wire from the device (for example, an alarm) to one of the relay output terminals 1 through 8.  
b. Connect a second wire from the relay device to the COM terminal.  
NOTE: The sensor input does not have to correspond numerically to the relay output. All sensor input and relay output actions  
are linked through programming. Refer to the Operation/Programming manual for details.  
Refer to the Operation/Programming manual for instructions on how to set up and operate the DX7000 DVR.  
C664M-B (8/02)  
9
 
SPECIFICATIONS  
ELECTRICAL/VIDEO  
Input Voltage:  
Signal System:  
CPU and RAM  
DX7008:  
100-240 VAC switchable, 50/60 Hz  
NTSC/PAL  
Celeron®, 128 MB  
DX7016:  
Pentium® III, 128 MB  
Resolution  
NTSC:  
PAL:  
320 x 240  
384 x 288  
M-JPEG  
Compression:  
Compressed Image Size: 352 x 240; average 6 KB  
Video Inputs:  
8 or 16, depending on model  
Video Outputs:  
Alarm Inputs:  
2 (1 SVGA, 1 analog)  
8
Control Outputs:  
Remote Control:  
Pan/Tilt/Zoom Control:  
8
Full remote control via PSTN, ISDN, TCP/IP  
RS-422 interface to receivers  
GENERAL  
Operating Temperature: 41° to 104°F (5° to 40°C)  
Relative Humidity:  
Dimensions:  
Maximum 80% non-condensing  
7 (H) x 17 (W) x 18 (D) inches (17.78 x 43.18 x 45.72 cm)  
(Design and product specifications subject to change without notice.)  
10  
C664M-B (8/02)  
 
REGULATORY NOTICES  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC  
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference  
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one  
or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment. Exceptions to this warranty are  
as noted below:  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to  
obtain a Repair Authorization number (RA), and provide the following information:  
1. Model and serial number  
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600  
Series); two years on all other cameras.  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Three years on Genex® Series (multiplexers, server, and keyboard).  
Two years all standard motorized or fixed focal length lenses.  
Two years on Legacy®, CamclosureCamera Systems, CM6700/CM6800/CM8500/CM9500/  
CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.  
Two years on Spectra®, Esprit, and PS20 Scanners, including when used in continuous  
motion applications.  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions  
stated above, please include a written explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by  
Pelco.  
Two years on WW5700 series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applica-  
tions (that is, preset scan, tour and auto scan modes).  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-  
9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA  
number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and  
freight should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the  
specific use or application made of the Products. Pelco’s liability for any claim, whether based on  
breach of contract, negligence, infringement of any rights of any party or product liability, relating  
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no  
event will Pelco be liable for any special, incidental or consequential damages (including loss of  
use, loss of profit and claims of third parties) however caused, whether by the negligence of  
Pelco or otherwise.  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:  
Intermediate Consignee  
American Overseas Air Freight  
320 Beach Road  
Burlingame, CA 94010  
USA  
Ultimate Consignee  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
USA  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
REVISION HISTORY  
Manual #  
C664M  
C664M-A  
C664M-B  
Date  
4/02  
5/02  
8/02  
Comments  
Original version.  
Revised installation instructions.  
Added information to Safeguards and Warnings.  
® Pelco, the Pelco logo, Spectra, Genex, Legacy, and Coaxitron are registered trademarks of Pelco.  
® Windows is a registered trademark of Microsoft Corporation.  
® Pentium and Celeron are registered trademarks of Intel Corporation.  
™ Esprit and Camclosure are trademarks of Pelco.  
© Copyright 2002, Pelco.  
All rights reserved.  
C664M-B (8/02)  
11  
 
®
World Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada  
 

Peavey Speaker SSE 15 User Manual
Peavey Stereo Amplifier PV 1500 User Manual
Philips CD Player CDR 795 User Manual
Philips Computer Monitor BDL4221VS User Manual
Philips Cordless Telephone SE7451B User Manual
Philips Network Card MIIC 201D U User Manual
Philips Stereo Amplifier BGY580 User Manual
Philips Stereo Amplifier TDA6111Q User Manual
Pioneer DVD Player BDP V6000 User Manual
Pitco Frialator Fryer SSH User Manual