Pelco Home Security System BK4000 BK4024 User Manual

®
EH4014/EH4018 Series  
Camera Enclosures  
Installation/Operation Manual  
C430M-E (1/95)  
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827  
 
REVISION HISTORY  
Manual #  
Date  
11/88  
4/90  
Comments  
C430M  
Original version.  
C430M  
Rev. A. Added EH4014-1/-2, EH4014/BR, EH4014/CH,  
EH4014/CP, EH4018-1/-2, and BK4000/BK4024 models. Fig-  
ure 2 revised to show current design. Sections 4.2.1 and  
4.2.2 revised to include new cable distances and heater kit  
installation procedures. Section 7 updated to include addi-  
tional hardware.  
C430M  
9/90  
Rev. B. Manual revised to include Section 1.1 for the UL  
compliance and listing.  
11/90  
11/90  
Addendum issued for addition of 230 VAC models.  
C430M  
C430M  
Rev. C. Sections 2.1 thru 2.4, 3.0, 4.2, 4.2.1, and Figures 2  
and 3 revised to include the addition of 230 VAC models.  
8/91  
1/93  
1/95  
Rev. D. Sections 2.3, 2.4 and Figure 3 revised to include  
additional mounts; revised voltages, power consumption and  
cable distances; and revised wiring diagram for heater/blower.  
Addendum issued to include installation instructions for out-  
door applications.  
C430M-E  
Rev. E. Revised to include new heater wattage values as  
per ECO #93-185, new component/assembly diagrams with  
updated BOM information as per ECO #93-187. Revised to  
show the removal of PC board when using blower kits only,  
with updated wiring diagrams, as per ECO #93-210. Incor-  
porated the use of CAPU0050.00/25 in 24 VDC blower kit  
wiring, as per ECO #94-447. Indoor/outdoor installation in-  
structions incorporated.  
9/95  
Parts list updated to show revised number for item 13.  
PELCO Manual C430M-E (1/95)  
iii  
 
(This page intentionally left blank.)  
iv  
PELCO Manual C430M-E (1/95)  
 
INSTALLATION/OPERATION MANUAL  
EH4014/EH4018 SERIES  
CAMERA ENCLOSURES  
1.0 WARNINGS  
Priortoinstallationanduseofthisproduct,thefollowing  
WARNINGS should be observed.  
4. Only use replacement parts recommended by  
PELCO.  
1. Installation and servicing should only be done by  
Qualified Service Personnel and conform to all  
Local codes.  
5. After replacement/repair of this unit’s electrical  
components, conduct a resistance measurement  
betweenlineandexposedpartstoverifytheexposed  
parts have not been connected to line circuitry.  
2. Unless the unit is specifically marked as a NEMA  
Type 3-6P enclosure, it is designed for Indoor use  
only and it must not be installed where exposed to  
rain and moisture.  
6. The installation method and materials should be  
capable of supporting four (4) times the weight of  
the enclosure, pan/tilt, camera, and lens  
combination.  
3. The product bears the following marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
CAUTION:  
TOREDUCETHERISKOFELECTRICAL  
SHOCK, DO NOT REMOVE COVER. NO  
USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
Please thoroughly familiarize yourself with the information in this manual  
prior to installation and operation.  
PELCO Manual C430M-E (1/95)  
1
 
2.0 SCOPE  
3.0 DESCRIPTION  
The information contained within this manual covers  
the EH4014/EH4018 Series camera enclosures.  
The EH4014 and EH4018 light-duty camera enclosures  
are designed for use with 2/3" cameras and will ac-  
commodate fixed focal length lenses or motorized zoom  
lenses with or without auto-iris operation.  
The EH4014 and EH4018 have been engineered for  
indoor and outdoor use when used in accordance with  
the installation instructions of this manual. They are of  
contemporary design for indoor applications and are  
fully sealed for outdoor applications.  
These enclosures have a removable rear cap for easy  
access to the slide-out, camera mount, platform. The  
adjustable glands on the rear cap allow for easy instal-  
lation and adjustments for cables and camera/lens. The  
removable front cap allows manual lens adjustments to  
be made without removing the camera/lens.  
Figure 1. EH4014/EH4018 Dimension Drawing  
2
PELCO Manual C430M-E (1/95)  
 
3.1 MODELS  
3.2 OPTIONS  
AFW4000  
EH4014  
Enclosure, indoor/outdoor extruded  
aluminum construction for 2/3" cam-  
eras and fixed focal length lenses up  
to 12" long. (UL, CE)  
Anti-fogging window  
BK4000  
Blower kit for EH4014/EH4018, 120  
VAC, 4 watts  
EH4014-1  
EH4014-2  
EH4014-3  
Same as EH4014 except maximum  
camera/lens length is 10.25" and unit  
is supplied with 120 VAC heater/  
blower. (UL)  
BK4024  
BK4220  
HK4014  
Blower kit for EH4014/EH4018, 24  
VAC, 3 watts  
Blower kit for EH4014/EH4018, 230  
VAC, 4.8 watts  
Same as EH4014 except maximum  
camera/lens length is 10.25" and unit  
is supplied with 24 VAC heater/  
blower. (UL, CE)  
Heater kit for EH4014/EH4018, 120  
VAC, 40 watts.Activates ON at 40°F;  
OFF at 60°F  
Same as EH4014 except maximum  
camera/lens length is 10.25" and unit  
is supplied with 230 VAC heater/  
blower. (CE)  
HK4024  
HK4220  
LK4000  
Heater kit for EH4014/EH4018, 24  
VAC, 40 watts.Activates ON at 40°F;  
OFF at 60°F  
Heater kit for EH4014/EH4018, 230  
VAC, 30 watts.Activates ON at 40°F;  
OFF at 60°F  
EH4014/BR  
EH4014/CH  
EH4014/CP  
EH4018  
Same as EH4014 with brass-plated  
finish.  
Same as EH4014 except chrome  
plated finish.  
Tamper-proof screw kit for EH4000  
Series.  
Same as EH4014 except copper  
plated finish.  
SS4014  
SS4018  
Sun shroud for EH4014  
Sun shroud for EH4018  
Enclosure, indoor/outdoor extruded  
aluminum construction for 2/3" cam-  
eras and fixed focal length lenses up  
to 16" long. (UL, CE)  
EH4018-1  
EH4018-2  
EH4018-3  
Same as EH4018 except maximum  
camera/lens length is 14.25" and unit  
is supplied with 120 VAC heater/  
blower. (UL)  
Same as EH4018 except maximum  
camera/lens length is 14.25" and unit  
is supplied with 24 VAC heater/  
blower. (UL, CE)  
Same as EH4018 except maximum  
camera/lens length is 14.25" and unit  
is supplied with 230 VAC heater/  
blower. (CE)  
NOTE: 230 VAC models are not listed by  
Underwriters Laboratories, Inc.  
PELCO Manual C430M-E (1/95)  
3
 
3.3 RECOMMENDED CABLE SIZE  
The following cable sizes are the minimum recom-  
mended for use with the combination of blower/heater/  
camera.  
CAUTION: When using a single power  
source for both the camera and accessories, the  
camera power consumption must be taken into  
consideration when determining wire gauge.  
Power  
Model Number  
Input Voltage  
120 VAC  
Consumption  
44 watts  
Cable Size  
Cable Distance  
EH4014-1/  
EH4018-1  
22 Awg  
20 Awg  
18 Awg  
16 Awg  
1,013 ft (308.8 m)  
1,612 ft (491.3 m)  
2,564 ft (781.5 m)  
4,070 ft (1,240.5 m)  
EH4014-2/  
EH4018-2  
24 VAC  
43 watts  
34.8 watts  
4 watts  
20 Awg  
18 Awg  
16 Awg  
14 Awg  
65 ft (19.8 m)  
100 ft (30.48m)  
165 ft (50.3 m)  
265 ft (80.8 m)  
EH4014-3/  
EH4018-3  
230 VAC  
120 VAC  
24 VAC  
20 Awg  
18 Awg  
16 Awg  
14 Awg  
7,488 ft (2,282 m)  
11,913 ft (3631 m)  
18,906 ft (5,763 m)  
30,161 ft (9,193 m)  
BK4000  
BK4024  
BK4220  
HK4014  
HK4024  
HK4220  
22 Awg  
20 Awg  
18 Awg  
16 Awg  
11,152 ft (3,399.1 m)  
17,733 ft (5,405.0 m)  
28,213 ft (8,599.3 m)  
44,776 ft (13,647.7 m)  
3 watts  
20 Awg  
18 Awg  
16 Awg  
14 Awg  
945 ft (288.0 m)  
1,500 ft (457.2 m)  
2,385 ft (726.9 m)  
3,805 ft (1,159.8 m)  
230 VAC  
120 VAC  
24 VAC  
4.8 watts  
40 watts  
40 watts  
30 watts  
20 Awg  
18 Awg  
16 Awg  
14 Awg  
54,289 ft (16,547.5 m)  
86,370 ft (26,326 m)  
137,075 ft (41,780 m)  
218,667 ft (66,650 m)  
22 Awg  
20 Awg  
18 Awg  
16 Awg  
1,115 ft (339.9 m)  
1,770 ft (539.5 m)  
2,820 ft (859.5 m)  
4,475 ft (1364.0 m)  
20 Awg  
18 Awg  
16 Awg  
14 Awg  
70 ft (21.3 m)  
110 ft (33.5 m)  
175 ft (55.3 m)  
285 ft (86.9 m)  
230 VAC  
20 Awg  
18 Awg  
16 Awg  
14 Awg  
8,686 ft (2,647 m)  
13,819 ft (4,212 m)  
21,932 ft (6,685 m)  
34,986 ft (10,664 m)  
4
PELCO Manual C430M-E (1/95)  
 
3.4 SPECIFICATIONS  
MECHANICAL  
Camera  
Weight:  
EH4014  
EH4014-1  
EH4014-2  
EH4014-3  
EH4018  
4 lbs. 4 oz. (1.91 kg)  
5 lbs. (2.25 kg)  
5 lbs. (2.25 kg)  
5 lbs. (2.25 kg)  
5 lbs. (2.25 kg)  
Mounting:  
Multiple holes on camera sled  
EH4018-1  
EH4018-2  
EH4018-3  
5 lbs. 12 oz. (2.59 kg)  
5 lbs. 12 oz. (2.59 kg)  
5 lbs. 12 oz. (2.59 kg)  
Camera Size:  
Accommodates camera/lens combi-  
nations up to:  
5.25" W x 3.50" H x  
12.00" L  
(EH4014)  
(EH4018)  
Shipping  
Weight:  
16.00" L  
(EH4014-1/EH4014-2/EH4014-3)  
(EH4018-1/EH4018-2/EH4018-3)  
10.25" L  
14.25" L  
EH4014  
6 lbs. (2.7 kg)  
EH4014-1  
EH4014-2  
EH4014-3  
EH4018  
EH4018-1  
EH4018-2  
EH4018-3  
6 lbs. 12 oz. (3.04 kg)  
6 lbs. 12 oz. (3.04 kg)  
6 lbs. 12 oz. (3.04 kg)  
7 lbs. (3.15 kg)  
7 lbs. 12 oz. (3.49 kg)  
7 lbs. 12 oz. (3.49 kg)  
7 lbs. 12 oz. (3.49 kg)  
Viewing  
Window:  
1/8" thick, optically clear, impact re-  
sistant Lexan (U.L. 94HB rated).  
Viewing area 2.50"H x 3.75"W.  
Cable Entry:  
Two compression glands on rear cap  
GENERAL  
Construction:  
Extruded aluminum body; injection-  
molded ABS black plastic end caps  
Finish:  
Textured, semigloss beige enamel  
(all models except /BR(brass), /CH  
(chrome), or /CP (copper)  
Dimensions:  
See Figure 1  
PELCO Manual C430M-E (1/95)  
5
 
4.0 INSTALLATION  
8. Replace the two (2) Phillips head screws.  
The following hardware is supplied with the enclosure  
and can be used to mount the enclosure or the camera/  
lens.  
IMPORTANT: When reinstalling the front  
or rear of the enclosure, make sure the end caps  
are firmly seated against the enclosure to in-  
sure proper sealing.  
Quantity  
Item  
9. Attach the enclosure to the appropriate mount or  
pan/tilt using the instructions provided.  
3
3
3
1/4-20 x .500 Hex head screws  
1/4 Flat washers  
1/4 Split washers  
10. If the housing is mounted such that the two mount-  
ing holes are facing up, and only one mounting  
hole is used, the other hole shall be plugged by a  
1/4"-20 bolt to prevent the entrance of water.  
4.1 CAMERA/LENS INSTALLATION  
To install the camera/lens, perform the following steps:  
11. All cables entering the enclosure shall employ a  
service loop to prevent the entrance of water.  
1. Remove the two (2) Phillips head screws from the  
rear cap.  
NOTE: If the lens needs to be adjusted after  
installation, it is easier to remove the front cap  
to make final lens adjustments.  
2. Remove the rear cap from the enclosure, pull out  
the sled assembly and remove it from the rail.  
3. Place the camera/lens on the sled assembly.  
NOTE: Position the camera/lens at the for-  
ward-most point on the sled, while allowing  
clearance between the lens and enclosure win-  
dow when the lens is adjusted to its maximum  
physical length.  
4. Secure the camera/lens to the sled with the 1/4-20  
hex head screws provided.  
5. Pull the video and power cables through the glands  
and attach to the camera. Adjust the glands for a  
tight fit around the cables. The cable glands are  
designed to be used with a single cable ranging in  
size from 0.187" (0.475 cm) to 0.312" (792 cm) in  
diameter.  
6. Adjust camera focus and iris if necessary.  
7. Replace the sled on the rail and slide the assembly  
into the enclosure until the cap is securely closed.  
6
PELCO Manual C430M-E (1/95)  
 
4.2 HEATER KIT INSTALLATION  
4.3 BLOWER KIT INSTALLATION  
Refer to Section 2.4, Recommended Cable Size, to de-  
termine cable size needed for installation. To install the  
heater and/or blower kits perform the following steps  
(refer to Figure 2):  
To install the BK4000/BK4024, perform the following  
steps:  
1. Remove the Phillips Head screws from the rear cap  
and slide the assembly out from the enclosure.  
1. Remove the Phillips head screws from the rear cap  
and slide the assembly out from the enclosure.  
2. Attach the blower assembly to the rear plate using  
two of the self-tapping screws holding the end cap  
to the sled.  
2. Attach the bracket with the terminal strip and heater  
thermostat to the rear plate using two (2) 6-32 self-  
tapping screws, mount onto the drilled-out holes.  
3. Wire according to the wiring diagram in Figure 3.  
3. Install the bracket with the heater pad onto the front  
of the sled using the 1/4-20 screw.  
NOTE: When used in conjunction with a  
heater kit, the blower can be wired into the ter-  
minal block on the P.C. Board.  
4. Wire according to the wiring diagram in Figure 3.  
Figure 2. Heater Bracket and Blower Installation  
PELCO Manual C430M-E (1/95)  
7
 
4.4 INSTALLATION PROCEDURES  
The following items are supplied in the heater and blower kits.  
Quantity  
Item  
PELCO Part No.  
Blower Kit  
Heater Kit  
1
1
1
4
4
1
1
1
1
2
1
1
1
1
1
1
1
PCB and blower bracket  
BK40004000COMP  
X
X
X
X
X
X
PCB and thermostat assy (24V/120V) PCB9000300ASSY  
PCB and thermostat assy  
PCB mounting screws, 6-32 x 3/8  
PCB insulating washers  
Heater bracket (24V/120V)  
Heater bracket (230V)  
Heater pad, 120V/40W  
Heater pad, 24V/40W  
Heater pad, 120V/15W  
Heater bracket mounting screw  
Fan, 120 VAC, 19 CFM  
Fan, 24 VDC, 19 CFM  
Resistor for fan, 3K ohm  
Bridge Rectifier Diode  
Capacitor  
PCB9100300ASSY  
ZH6-32X.375SPP  
ZH200X437X62N  
HK40244000COMP  
HK2304000COMP  
EHWD10087  
EHHK10087  
HK300010115  
ZH1/420X.375SPP  
MM750010003  
ED210005  
RES003.0K10.0  
DIOMDA104  
24/120 VAC models  
230 VAC model  
120 VAC model  
24 VAC model  
230 VAC model  
All heater models  
120 & 230 VAC models  
24 VAC model  
230 VAC model  
24 VAC model  
24 VAC model  
CAPU0050.0/25  
BK7044002COMP  
Component Bracket  
24 & 230 VAC models  
Input, AC High  
Input, AC (neutral)  
Ground  
Input, AC High  
Input, AC (neutral)  
Ground  
1
2
1
2
3
4
5
6
Cap  
3
4
Fan  
Fan  
5
6
Diode  
Bridge  
7
7
8
8
Thermostat  
9
9
10  
Heater  
Heater  
10  
120 VAC Model  
24 VAC Model  
Input, AC High  
Input, AC (neutral)  
Ground  
1
2
3
4
Fan  
5
6
7
Resistor  
8
9
Heater  
10  
Heater/Blower wiring  
diagrams using  
Heater Kit with PCB.  
Heater  
230 VAC Model  
Butt Splices Provided  
Diode Bridge  
AC  
Cap  
120 VAC (BK4000)  
24 VAC (BK4024)  
Blower Wiring  
Installation only.  
Resistor  
PCB not required.  
230 VAC (BK4220)  
Figure 3. Heater/Blower Wiring Diagram  
8
PELCO Manual C430M-E (1/95)  
 
4.5 SUN SHROUD INSTALLATION  
5. Put the cap back on the enclosure and fasten down  
with the screws.  
The sun shroud protects the enclosure from the direct  
rays of the sun and reduces internal temperature by  
approximately 10-15°. To install the sun shroud, per-  
form the following steps (refer to Figure 4).  
NOTE: Be sure the screws are tightened down  
to secure the seal between the cap and the en-  
closure.  
1. Remove the two (2) screws from the front or rear  
end cap of the enclosure.  
5.0 CARE AND MAINTENANCE  
2. Remove the cap.  
Regularly scheduled maintenance will help prolong the  
operational life and appearance of the equipment. Clean  
the window regularly with a mild nonabrasive deter-  
gent in water and with a soft cloth to help maintain  
picture clarity.  
3. Align the guides on the sun shroud with the runner  
on the enclosure.  
4. Slide the sun shroud until the bottom guides on the  
sun shroud meet the opposite end cap.  
Figure 4. Sun Shroud Installation  
PELCO Manual C430M-E (1/95)  
9
 
6.0 EXPLODED ASSEMBLY DIAGRAM/ PARTS LIST  
The following parts list corresponds to the exploded assembly diagram in Figure 5.  
Item  
Quantity  
Description  
Part Number  
1
2
3
4
5
6
7
2
1
2
2
1
1
1
1
1
1
4
7
4
1
2
2
1
1
2
4
1
Gasket, front/rear (not shown)  
Front cap, black  
EH400010000  
EH400010006  
Gland, SL9  
EH400010003  
EH400010004  
EH40004007COMP  
EH400010005  
Counter nut, GMP-9  
Sled bracket  
Rear end cap, black  
Body, 14" enclosure (EH4014 only)  
Body, 18" enclosure (EH4018 only)  
Sled (EH4014)  
EH40144000COMP  
EH40184000COMP  
EH40144001COMP  
EH40184001COMP  
ZH8-32X.500SPP  
ZH8-SBTX.500SPP  
ZH260X562X65C  
EH400010009  
8
Sled (EH4018)  
9
Screw, 8-32 x .500, pan head, Phil SS  
Screw, #8 x 1/2" Type A, Pan, Phil SS  
Washer, flat, 3/16 USS spl-size pltd  
Window, 4.453"W x 3.031"H x .125" thick (Lexan)  
NP gasket 1/8 x 1/8 ft (not shown)  
Screw, 1/4-20 x 1/2" hex cad C/S SS (not shown)  
Screw, 1/4-20 x 3/8" pan, Phil SS (not shown)  
Washer, internal star 1/4" SS (not shown)  
Washer, split lock 1/4" SS (not shown)  
Screw, 6-32 x 3/8" Type F Phil Pan SS (not shown)  
Installation kit, enclosure hardware (not shown)  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
EH110042  
ZH1/4-20X.500CH  
ZH1/420X.375SPP  
ZH1/4LWSIS  
ZH1/4LWSSL  
ZH6-SFX.375SPP  
IK1000  
Figure 5. EH4014/EH4018 Exploded Assembly Diagram  
10  
PELCO Manual C430M-E (1/95)  
 
7.0 WARRANTY AND RETURN  
INFORMATION  
WARRANTY  
RETURNS  
Pelco will repair or replace, without charge, any merchandise proved  
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate  
of shipment.  
In order to expedite parts returned to the factory for repair or credit, please  
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an  
authorization number (CA number if returned for credit, and RA number  
if returned for repair).  
Exceptions to this warranty are as noted below:  
All merchandise returned for credit may be subject to a 20% restocking  
and refurbishing charge.  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and  
keyboard).  
Three years on Camclosure® and fixed camera models, except the  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,  
and MC3651H-2X camera models, which have a five-year warranty.  
Goods returned for repair or credit should be clearly identified with the  
assigned CA or RA number and freight should be prepaid. Ship to the  
appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto  
Rico, send goods to:  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and  
DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, includ-  
ing when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding  
wiper blades).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto  
Rico and are instructed to return goods to the USA, you may do one of the  
following:  
Eighteen months on DX Series digital video recorders, NVR300  
Series network video recorders, and EnduraSeries distributed  
network-based video products.  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
One year (except video heads) on video cassette recorders (VCRs).  
Video heads will be covered for a period of six months.  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods  
to:  
Six months on all pan and tilts, scanners or preset lenses used in  
continuousmotionapplications(thatis,presetscan,tourandautoscan  
modes).  
Pelco c/o Expeditors  
473 Eccles Avenue  
Pelco will warrant all replacement parts and repairs for 90 days from the  
date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to Pelco, Clovis, California. Repairs made necessary by  
reason of misuse, alteration, normal wear, or accident are not covered  
under this warranty.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco assumes no risk and shall be subject to no liability for damages or  
loss resulting from the specific use or application made of the Products.  
Pelco’s liability for any claim, whether based on breach of contract,  
negligence, infringement of any rights of any party or product liability,  
relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special,  
incidental or consequential damages (including loss of use, loss of profit  
and claims of third parties) however caused, whether by the negligence  
of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The  
Dealer may also have additional rights, which are subject to variation from  
state to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800)  
289-9100 or (559) 292-1981 to obtain a Repair Authorization number  
(RA), and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice  
number  
3. Details of the defect or problem If there is a dispute regarding the  
warranty of a product which does not fall under the warranty conditions  
stated above, please include a written explanation with the product  
when returned.  
Method of return shipment shall be the same or equal to the method by  
which the item was received by Pelco.  
PELCO Manual C430M-E (1/95)  
11  
 
®
PELCO  
(559) 292-1981 • (800) 289-9100 • FAX (559) 292-3827 or (800) 289-9150  
International customers call 1-559-292-1981 or FAX 1-559-348-1120  
(Product specifications subject to change without notice.)  
12  
PELCO Manual C430M-E (1/95)  
 

Peavey Stereo Equalizer PV 231EQ User Manual
Philips Clock Radio SA3104 User Manual
Philips CRT Television TS 2746C User Manual
Philips Flat Panel Television 15PF9925 12S User Manual
Philips Stereo System MZ3 User Manual
Philips TV Cables SWV6371 User Manual
Polaroid Flat Panel Television PLA 4250A User Manual
Polaroid Portable Generator BLL Generator User Manual
Precor Treadmill C966 User Manual
ProForm Treadmill 495 LS User Manual