Pelco Marine Radio C528M E User Manual

I N S T A L L A T I O N / O P E R A T I O N  
MPTAZ Series Pan/Tilt  
and Scanner Control  
®
C528M-E (4/03)  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.  
2. Unless the unit meets NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P standards, it is designed for indoor use only and it must not be  
installed where exposed to rain and moisture.  
3. Only use replacement parts recommended by Pelco.  
4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and  
exposed parts to verify the exposed parts have not been connected to line circuitry.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of  
electric shock is present within this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important operating and mainte-  
nance instructions in the literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.  
C528M-E (4/03)  
3
 
DESCRIPTION  
The controls in the MPTAZ Series operate 120 VAC, 230 VAC, and 24 VAC pan/tilts or scanners. All models include auto/  
random/manual scan operation, pan/tilt operation with a joystick, and lens control.  
MODELS  
MPTAZ24DT  
Desktop joystick control module for 24 VAC pan/tilts and scanners, 120 VAC input (FCC, Class A)  
Same as MPTAZ24DT except 230 VAC input (CE)  
Desktop joystick control module for 120 VAC pan/tilts and scanners, 120 VAC input (FCC, Class A)  
Desktop joystick control module for 230 VAC pan/tilts, 230 VAC input  
MPTAZ24DT/220  
MPTAZ115DT  
MPTAZ220DT  
4
C528M-E (4/03)  
 
INSTALLATION  
The MPTAZ Series Control is shipped from the factory for pan/tilt operation. If you are connecting the control to a pan/tilt, skip  
step 1 and proceed to step 2, Electrical Connections.  
1. To operate a scanner with the MPTAZ Series, reset the control’s jumper JP5 to the SCANNER position. Jumper JP5 is  
factory set in the P/T position. Refer to Figure 1 for the internal configuration of the PC board.  
Figure 1. PC Board Configuration  
C528M-E (4/03)  
5
 
2. Electrical Connections - Follow the correct instructions for your control model.  
Cable Distances:  
Pan/Tilt  
or Scanner Refer to the installation manual for the specific scanner or pan/tilt to be used with the control.  
Lens  
The following lens distances are the approximate maximum recommended under the following conditions:  
Based on a 35 mA load @ 12 VDC  
Single lens function activation  
10% line loss in voltage at the lens motor  
22 AWG  
20 AWG  
18 AWG  
(0.3 mm2)  
(0.5 mm2)  
(1.0 mm2)  
1,062 ft (323 m)  
1,688 ft (514 m)  
2,686 ft (818 m)  
MPTAZ24DT and MPTAZ24DT/220 - Wire the connecting cable from the pan/tilt or scanner to the control. Refer to one  
of the following wiring diagrams: Figure 2 (scanners) or Figure 3 (pan/tilts). Proceed to step 3.  
NOTE: When a relay box (RB24/RB115) is used with a scanner, the AUTO SCAN mode requires special connections;  
consult factory for details.  
PT COMM  
LEFT  
RIGHT  
UP  
TO SCANNER  
CONNECTOR  
DOWN  
AUTO  
ZOOM  
FOCUS  
IRIS  
LENS COM  
TO LENS  
CONNECTOR  
1
2
3
4
5
6
7
8
9
10  
CONTROLLER OUTPUT  
TERMINAL STRIP  
Figure 2. MPTAZ24DT, MPTAZ24DT/220 Wiring Diagram for Scanners and Lenses  
PT COMM  
LEFT  
RIGHT  
UP  
TO PAN/TILT  
CONNECTOR  
DOWN  
AUTO  
ZOOM  
FOCUS  
IRIS  
LENS COM  
TO LENS  
CONNECTOR  
1
2
3
4
5
6
7
8
9
10  
CONTROLLER OUTPUT  
TERMINAL STRIP  
Figure 3. MPTAZ24DT, MPTAZ24DT/220 Wiring Diagram for Pan/Tilts and Lenses  
6
C528M-E (4/03)  
 
MPTAZ115DT or MAPTAZ220DT - Assemble the mating connector. Refer to Figure 4 and perform the following steps.  
a. Slide the connector clamp assembly over the conductor cable. If the diameter of the conductor cable is such that the rubber  
boot will slide over it easily, slide the rubber boot onto the conductor cable at this time. If not, discard the rubber boot.  
b. Refer to Detail A in Figure 4. Prepare the wires from the conductor cable as follows:  
Strip at least one inch (2.54 cm) from the cable jacket to expose the wires. You may need to strip more from  
the cable jacket if you have more wires.  
Strip .125-inch (3 mm) from each wire.  
Use an AMP style crimper, crimp the wires and their insulation to the connector pins.  
NOTE: Contacts cannot be removed from the connector without the use of the appropriate AMP extraction tool  
(ZT305183), which is available from Pelco.  
c. Slide the connector pins into the appropriate holes in the connector body until they snap into place. Refer to detail B  
in Figure 4 and to Figures 5 and 6 for the correct pin arrangement.  
d. Push the connector clamp assembly (with boot, if used) toward the connector body. Screw the clamp assembly onto  
the connector body, being careful not to disturb the wires.  
e. To complete the assembly, attach the appropriate clamp with the screws provided and tighten.  
f. Wire the connecting cable from the pan/tilt or scanner to the controller. Refer to one of the following wiring  
diagrams: Figure 5 (scanners) or Figure 6 (pan/tilts).  
3. Plug the control’s power cord into an AC outlet. The unit powers-up in manual operation mode; the MANUAL LED turns on.  
1/8"  
1"  
FRONT VIEW  
OR  
3
1
7
4
8
11  
14  
12  
Figure 4. Connector Assembly  
1
3
1
3
4
PT COMMON  
LEFT  
PT COMMON  
LEFT  
4
AUTO  
AUTO  
5
5
DOWN  
UP  
DOWN  
UP  
TO SCANNER  
CONNECTOR  
TO PAN/TILT  
CONNECTOR  
6
6
7
7
8
RIGHT  
RIGHT  
8
SAFTY GND  
IRIS  
SAFTY GND  
IRIS  
10  
12  
11  
13  
10  
12  
ZOOM  
ZOOM  
TO LENS  
CONNECTOR  
TO LENS  
CONNECTOR  
11  
13  
FOCUS  
LENS COM  
FOCUS  
LENS COM  
Figure 5. MPTAZ115DT, MPTAZ220DT Wiring  
Figure 6. MPTAZ115DT, MPTAZ220DT Wiring  
Diagram for Scanners and Lenses  
Diagram for Pan/Tilts and Lenses  
C528M-E (4/03)  
7
 
OPERATION  
To operate the MPTAZ Series Control, use the push buttons to control the lens, and move the joystick to control the pan/tilt or  
scanner.  
The MPTAZ Series Control has two modes of automatic pan/tilt operation: random scan and auto scan.  
Random activation causes scanning between the limit stops in an unpredictable pattern.  
To activate random mode, press the SELECT switch until the LED next to RANDOM is lit.  
Auto scan will operate the pan/tilt between limits for 30 minutes. After 30 minutes, the control returns to the random scan  
mode. To activate auto scan, press the SELECT switch until the LED next to AUTO is lit.  
To return to manual mode, move the joystick to the left or right. The control will also return to manual operation if power is lost  
and restored.  
8
C528M-E (4/03)  
 
MAINTENANCE  
Under normal operating conditions and usage, maintenance of this equipment is not necessary. However, if maintenance is  
required, contact a qualified service technician or return to the factory for repair.  
C528M-E (4/03)  
9
 
SPECIFICATIONS  
ELECTRICAL  
Input Voltage  
MPTAZ115DT,  
MPTAZ24DT:  
MPTAZ24DT/220,  
MPTAZ220DT:  
120 VAC, 50/60 Hz  
230 VAC, 50/60 Hz  
Output Voltage  
MPTAZ24DT,  
MPTAZ24DT/220:  
MPTAZ115DT:  
MPTAZ220DT:  
24 VAC  
120 VAC  
230 VAC  
0-12 VDC  
Lens Voltage:  
Fuse Protection  
MPTAZ115DT,  
MPTAZ24DT:  
1 ASB  
MPTAZ24DT/220,  
MPTAZ220DT:  
0.5 ASB  
Power Cord:  
Connectors  
MPTAZ115DT,  
3-wire grounded, #18 AWG  
MPTAZ220DT:  
MPTAZ24DT,  
AMP CPC type  
MPTAZ24DT/220:  
Conductor Requirements:  
10-position terminal strip  
(No additional conductors required for auto/random scan operation)  
9 plus ground for MPTAZ115DT or MPTAZ220DT (when used with pan/tilt and lens)  
8 plus ground for MPTAZ115DT (when used with scanner and lens)  
9 and no ground for MPTAZ24DT or MPTAZ24DT/220 (when used with pan/tilt and lens)  
8 and no ground for MPTAZ24DT or MPTAZ24DT/220 (when used with scanner and lens)  
GENERAL  
Construction  
Cover:  
Chassis:  
Steel, black polyester powder coat  
Steel, zinc plated  
Panel:  
Aluminum, black polyester powder coat with white silkscreen  
Approximate Weight  
MPTAZ115DT:  
MPTAZ220DT:  
MPTAZ24DT:  
MPTAZ24DT/220:  
5.17 lb (2.34 kg)  
5.17 lb (2.34 kg)  
6.48 lb (2.94 kg)  
6.59 lb (2.99 kg)  
(Design and product specifications subject to change without notice.)  
10  
C528M-E (4/03)  
 
REGULATORY NOTICES  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC  
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated  
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the  
interference at his own expense.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
C528M  
Date  
1992  
10/92  
10/93  
8/95  
Comments  
Original version.  
Revised installation instructions; added Figure 7.  
Revised to include MPTAZ24DT/220.  
Revised Figures 2 and 7.  
C528M-A  
C528M-B  
C528M-C  
C528M-D  
C528M-E  
11/99  
4/03  
Revised installation instructions. Updated manual to new format.  
Revised operation instructions; added FCC, Class A statement. Updated manual to new format.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
Pelco, the Pelco Logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
© Copyright 2003, Pelco. All rights reserved.  
C528M-E (4/03)  
11  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Peavey Stereo Equalizer PV 231EQ User Manual
Pentair Electric Heater MiniMax NT LN User Manual
Pentair Swimming Pool Vacuum Kreepy Kruiser User Manual
Philips Door Swa 2522 User Manual
Philips DVD VCR Combo DVP3055V 02 User Manual
Philips Personal Computer SGC5101BD User Manual
Planar Car Video System LA1950R User Manual
Precision Power MP3 Player DAC348 User Manual
Professional Series Refrigerator PS72122 User Manual
PYLE Audio MP3 Docking Station PIWPD3 User Manual