Planet Technology Switch POE 152S 12V User Manual

IEEE 802.3af  
Power over Ethernet Splitter  
POE-152S-5V/12V  
User’s Manual  
- 1 -  
 
TABLE OF CONTENTS  
1. INTRODUCTION.......................................................................................................................................... 4  
1.1 CHECKLIST ................................................................................................................................................ 4  
1.2 ABOUT THE POWER OVER ETHERNET SPLITTER .......................................................................................... 4  
1.3 FEATURES ................................................................................................................................................. 4  
1.4 SPECIFICATION .......................................................................................................................................... 5  
1.5 PRODUCT OUTLOOK................................................................................................................................... 5  
2. HARDWARE INSTALLATION..................................................................................................................... 6  
2.1 BEFORE INSTALLATION............................................................................................................................... 6  
2.2 POE-152 AND POE-152S, THE IEEE 802.3AF INJECTOR AND SPLITTER INSTALLATION................................ 7  
2.3 CONNECT WITH IEEE 802.3AF DEVICES...................................................................................................... 8  
3.TROUBLESHOOTING................................................................................................................................... 9  
APPENDIX A NETWORKING CONNECTION ............................................................................................... 10  
A.1 SWITCHS RJ-45 PIN ASSIGNMENTS......................................................................................................... 10  
A.2 RJ-45 CABLE PIN ASSIGNMENT................................................................................................................. 10  
- 3 -  
 
1. INTRODUCTION  
1.1 Checklist  
Thank you for purchasing our POE-152S IEEE 802.3af Power over Ethernet Splitter, your Power over Ethernet  
Splitter package shall contain following contents:  
Check the contents of your package for following parts:  
ò
ò
ò
ò
Power over Ethernet Splitter x 1  
User's manual CD x 1  
DC Plug Cable x 2  
15cm UTP straight network cable x 1  
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the orig  
use them against to repack the product in case there is a need to return it to us for repair.  
1.2 About the Power over Ethernet Splitter  
The PLANET POE-152S is an IEEE 802.3af Power over Ethernet device that split the 48V DC over the Ethernet cable into  
5/12V DC power output. Work with the IEEE 802.3af power source equipment (PSE), the POE-152S frees the device  
deployment from restrictions due to power outlet locations, which eliminate the costs for additional AC wiring and reduces  
the installation time.  
When the PSE inserts DC Voltage into the CAT 5 cable, it allows the cable between the PSE and POE-152S to transfer  
data and power simultaneously. The maximum distance between the PSE and POE-152S is 100M. With being installed,  
the PSE combines the Ethernet digital data with power over the twisted pair cables as an injector, and POE-152S, the  
splitter, shall separate the digital data and the power into two outputs.  
With IEEE 802.3af Power over Ethernet being installed, the system administrator only has to use a single RJ-45 Ethernet  
cable to carry both power and data to each device. The POE-152S also have the benefits of cost saving, as well as ease  
for networking planning and higher reliability. Furthermore, upon any IEEE 802.3af being installed, the POE-152S can  
make the connection while migrating or splitting the power and the Ethernet digital packets. Providing two kinds of DC  
output, the POE-152S offers 2.5A and 1A DC for current model POE-152S-5V and POE-152S-12V.  
1.3 Features  
Complies with IEEE 802.3af, Power over Ethernet, IEEE 802.3/802.3u/802.3ab 10/100/1000Base-T  
Splits the 48V DC power over RJ-45 Ethernet cable into different DC output  
LED indicators power input indication  
Distance up to 100 meters  
Choice of splitter for 5V DC and 12V DC  
Auto-detect of POE IEEE 802.3af equipment, protect devices from being damaged by incorrect installation  
Works with EIA568, category 5/5e/6,2/4-pair cables for 10Base-T or 100Base-TX and 1000Base-T  
- 4 -  
 
1.4 Specification  
Model  
POE-152S  
Ethernet Connector  
Ethernet Data Rate  
Output Voltage/Current  
2 x RJ-45 (1 for Data + DC in, 1 for Data out)  
10/100/1000Mbps (vary on Ethernet device attached)  
Vary on model:  
POE-152S-5V: 5VDC, 2.5A max.  
POE-152S-12V: 12VDC, 1A max.  
1
TIA/EIA-568, Category 5/5e/6 cable  
1 x POE ready/in-use  
Number of Device can be powered  
Ethernet Cable  
LED indicator  
Operating environment  
Storage environment  
Dimension (W x D x H)  
Weight  
0~50 Degree C, 5%~90%RH  
-20~70 Degree C, 5%~90%RH  
73 × 55 × 24 mm  
50g  
Emission  
FCC Class B, CE mark  
Standard Compliance  
IEEE 802.3 Ethernet  
IEEE 802.3u Fast Ethernet  
IEEE 802.3ab Gigabit Ethernet  
IEEE 802.3af Power over Ethernet  
1.5 Product Outlook  
LED definition:  
LED  
Color  
Function  
Lights to indicate the port is providing 48VDC in-line power.  
PoE ready / in-use  
Green  
- 5 -  
 
2. HARDWARE INSTALLATION  
These products provide three different running speeds – 10Mbps, 100Mbps,1000Mbps. in the same device and auto-  
matically distinguish the speed of incoming connection.  
This section describes the hardware features of POE-152S. Before connecting any network device to the POE-152S, read  
this chapter carefully.  
2.1 Before Installation  
Before your installation, it is recommended checking your network environment. If there is any issue for your install a  
networked device where is very difficult to find a power socket for your AC-DC adapter, the POE-152S can work with  
POE-152 IEEE 802.3af Power over Ethernet Injector with an AC-DC adapter(DC 48V input). The POE-152S provide you  
a way to provide DC power for this Ethernet device conveniently and easily.  
The10/100/1000Mbps speed duplex mode from Ethernet port of POE-152S depends on which Ethernet device attached.  
@Notice:  
The POE-152 and POE-152S can be installed in pair. However, the use of third-party device is allowed if the device  
complied with IEEE 802.3af standard.  
- 6 -  
 
2.2 POE-152 and POE-152S, the IEEE 802.3af Injector and Splitter installation  
1. Connect a standard network cable from “Ethernet+DC” of POE-152 to “Ethernet+DC” of POE-152S. The POE LED of  
POE-152 / POE-152S will light on continuance. The screen in Figure 1 appears.  
From POE-152 or IEEE 802.3af  
Power Supply equipment  
Figure 1: Connection to POE-152 or IEEE 802.3af POE equipment  
2. Connect the UTP cable in the package from “Ethernet” of POE-152S to the RJ-45 port of remote device.  
3. Connect proper DC plug from “DC OUT” of POE-152S to remote device.  
4. Power on the remote device and the LED indicator on POE-152S will remains on, the screen in Figure 2 appears.  
Figure 2: Connection architecture over POE-152/152S  
@Notice:  
1. The POE-152S only accept IEEE 802.3af power supply equipment, any other in-line power device sending power  
through UTP wire connects to POE-152S may cause the POE-152S malfunction.  
2. Please ensure the output voltage is correct before applying power to remote device.  
- 7 -  
 
2.3 Connect with IEEE 802.3af devices  
The POE-152S can also provide the alternative to make the non- IEEE 802.3af devices the possibility to connect with an  
IEEE 802.3af in-line power device like Power over Ethernet Switch, then connect proper DC plug from "DC OUT" of  
POE-152S to remote device. The screen in Figure 3 appears.  
Figure 3: Connect to IEEE 802.3af device  
Once POE-152S detects the existence of an IEEE 802.3af device, the LED indicator will be steady; ON to shows it is  
getting power.  
- 8 -  
 
3.TROUBLESHOOTING  
This chapter contains information to help you solve issues. If the POE-152S is not functioning properly, make sure the  
POE-152S was set up according to instructions in this manual.  
The PoE LED is not lit  
Solution:  
Check the cable connection between POE-152S and IEEE 802.3af device.  
Why the device connected to POE-152S cannot be powered?  
Solution:  
1. Please check the POE-152S is connect with an IEEE 802.3af complied in-line device like POE-152, and check if  
the POE LED indicator at POE-152S is steady blink once attach to the IEEE 802.3af in-line power device. Then  
connect the DC plug cable to the device you would like to power on.  
2. Please check the cable type of the connection from one end to the other end. The cable should be an 8-wire  
UTP, Category 5 or above, EIA568 cable within 100 meters. A cable with only 4-wire, short loop or over 100  
meters, all will affect the power supply.  
3. Please check the power requirement of the device you would like to power and check the label of the POE-152S  
if it meets the requirement. There are two models of POE-152S for different power output, DC 5V and DC 12V.  
4. Please check the specification of the powered device. If the device is over the specification of POE-152S, the  
LED indicator of POE-152S will blink instead of stead green. The maximum currents that POE-152S can supply  
are: 2.5A (5V DC) and 1A (12V DC).  
10/100/1000Base-T port link LED is lit, but the traffic is irregular  
Solution:  
Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch to  
change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.  
- 9 -  
 
APPENDIX A NETWORKING CONNECTION  
A.1 Switch‘s RJ-45 Pin Assignments  
1000Mbps, 1000Base T  
Contact  
MDI  
MDI-X  
1
2
3
4
5
6
7
8
BI_DA+  
BI_DA-  
BI_DB+  
BI_DC+  
BI_DC-  
BI_DB-  
BI_DD+  
BI_DD-  
BI_DB+  
BI_DB-  
BI_DA+  
BI_DD+  
BI_DD-  
BI_DA-  
BI_DC+  
BI_DC-  
10/100Mbps, 10/100Base-TX  
RJ-45 Connector pin assignment  
MDI  
MDI-X  
Contact  
Media Dependant  
Interface  
Media Dependant  
Interface -Cross  
1
2
Tx + (transmit)  
Tx - (transmit)  
Rx + (receive)  
Rx + (receive)  
Rx - (receive)  
Tx + (transmit)  
3
4, 5  
6
Not used  
Rx - (receive)  
Tx - (transmit)  
7, 8  
Not used  
A.2 RJ-45 cable pin assignment  
The standard RJ-45 receptacle/connector  
- 10 -  
 
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation  
and color of straight cable and crossover cable connection:  
Figure A-1: Straight-Through and Crossover Cable  
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the  
cables into your network.  
2080-A31120-001  
- 11 -  
 

Phase Technology Speaker CM5800i User Manual
Philips Clock Radio ORT7500 User Manual
Philips CRT Television 14PT1686G User Manual
Philips Portable DVD Player PD7000B User Manual
Philips Switch US2 PH1620 User Manual
Planet Technology Network Router VC 204 User Manual
Polk Audio Speaker ATRIUM45 User Manual
Polk Audio Speaker RM7400T RM40T User Manual
Porter Cable Staple Gun NS100B User Manual
Poulan Chainsaw 2250LE 2450LE 2550 LE Series User Manual