Pelco DVR C2968M A User Manual

I N S T A L L A T I O N / O P E R A T I O N  
KBD300USBKIT  
For use with DX4500/DX4600 DVRs  
and DS ControlPoint Software  
C2968M-A (10/09)  
 
Contents  
C2968M-A (10/09)  
3
 
List of Illustrations  
8
4
C2968M-A (10/09)  
 
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one blade wider than the  
other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the  
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from  
the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Only use with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus combination to avoid injury from tip-over.  
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-  
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
14. Unplug the apparatus during lightning storms or when unused for long periods of time.  
15. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.  
16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.  
17. Installation should be done only by qualified personnel and conform to all local codes.  
18. Unless this unit is specifically marked as NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not  
be installed where exposed to rain and moisture.  
19. Only use installation methods and materials capable of supporting four times the maximum specified load.  
20. Only use replacement parts recommended by Pelco.  
21. Avoid touching the screen directly with your fingers as the oils from your skin may be difficult to remove from the LCD.  
22. Do not apply direct pressure on the screen.  
23. Keep the monitor in a dust-free environment and away from strong electromagnetic fields.  
24. Do not use attachments, such as mounts, that are not recommended by Pelco. They may be hazardous.  
25. Do not place the monitor on an unstable stand, bracket, or mount. The unit may fall, causing serious damage to the unit or injury to a  
person. Only use mounts recommended by Pelco.  
26. A CCC-approved power cord must be used to power this equipment when used in China.  
27. A still image displayed too long may cause permanent damage to the LCD panel. Watching the LCD in 4:3 format for a long time may leave  
traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Using a  
camera or a system may cause a similar effect to the screen. Damages caused by this effect are not covered by the warranty.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a risk of electric shock is present  
within this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important operating and maintenance instructions in  
the literature accompanying this unit  
6
C2968M-A (10/09)  
 
 
Description  
The KBD300USBKIT is a required accessory if you want to interface the KBD300A keyboard to the DX4500/DX4600 Series digital video recorder  
(DVR). The KBD300USBKIT is also required to control certain functions of the Digital Sentry® (DS) ControlPoint software.  
This manual describes how to install and operate the KBD300A with the DX4500/DX4600 DVR and DS ControlPoint.  
DX4500/DX4600 SERIES DIGITAL VIDEO RECORDER  
The DX4500/DX4600 can be updated to support the optional KBD300A keyboard. You can use the keyboard to operate PTZ cameras connected to  
the unit.  
NOTE: DX4500/DX4600 version 1.2 DVR hardware cannot be updated to support the Pelco C (Coaxitron®) protocol feature.  
DS CONTROLPOINT  
Pelco’s KBD300A keyboards can be used to control certain functions of the DS ControlPoint software. To use a KBD300A with DS ControlPoint,  
your hardware and software must meet the following requirements:  
KBD300A version 5.7 or later  
DS ControlPoint version 6.7.1.99 or later  
Available serial port (COM) on the computer running DS ControlPoint  
MODELS  
KBD300USBKIT  
KBD300A adapter (120 VAC)  
KBD300USBKIT-X KBD300A adapter (230 VAC)  
PARTS LIST  
Qty Description  
1
1
1
1
USB to RS-232C cable  
PV140 RS-232 to RS-422 converter kit  
KBDKIT/KBDKIT-X wiring kit (includes two RJ-45 wall blocks and a 120 VAC/230 VAC to 12 VAC transformer)  
PV140 power supply (not used)  
C2968M-A (10/09)  
7
 
         
Installation  
DX4500/DX4600 SERIES DVR  
DX4500/DX4600 DVRs now support the use of the KBD300A keyboard. You must install the KBD300USBKIT to connect a KBD300A keyboard to a  
DX4500/DX4600.  
NOTES:  
DX4500/DX4600 version 1.2 DVRs do not support Pelco C (Coaxitron) protocol, regardless of software version.  
The units firmware and application software must be updated to version 1.3 before connecting or using a KBD300A keyboard (refer to  
CONNECTING TO A DX4500/DX4600  
Figure 1 shows how to connect the keyboard to the DX4500/DX4600.  
PIN 8  
PIN 7  
PIN 8  
PIN 1  
12 VAC  
PIN 2  
PIN 1  
PIN 8 = RX+  
PIN 7 = RX-  
.
.
.
.
PIN 2 = TX-  
PIN 1 = TX+  
Figure 1. DX4500/DX4600 Wiring Diagram  
WARNING: Do not connect the included PV140 power supply. The PV140 receives power from the DX4500/DX4600 and does not need a  
separate power supply.  
DX4500/DX4600 Series DVR: Contains one USB 2.0 connector on the front panel and two USB 2.0 connectors on the back panel.  
KBD300A Keyboard: Controls PTZ cameras connected to the DX4500/DX44600. A 25-foot (7.6 m) RJ-45 cable is supplied with the  
keyboard. The RJ-45 cable connects the terminal block to the KBD300A keyboard.  
8
C2968M-A (10/09)  
 
       
Keyboard Data and DIP Switch Cover: Contains the keyboard configuration switches. Use the switches to configure the keyboard  
address and operational mode (refer to Figure 2).  
1
2
3
4
5
6
7
8
ON  
DOWN = ON  
Figure 2. KBD300A Switch Settings: DX4500/DX4600 Operation  
RJ-45 Connector: Connects the KBD300A to the terminal block using the RJ-45 cable.  
KBDKIT/KBDKIT-X: The keyboard wiring kit that provides power for the KBD300A keyboard and interfaces the keyboard to the PV140.  
The kit includes two RJ-45 wall blocks and a 120 VAC/230 VAC to 12 VAC transformer.  
Table A. RJ-45 Wall Block Pinouts  
Pin Signal  
Pin Signal  
1
2
3
4
TX+  
5
6
7
8
GND  
N/A  
RX-  
TX-  
12 VAC/DC  
Nonpolar  
RX+  
PV140: A user-supplied interconnect cable (shielded twisted pairs) is required to connect the PV140 to the terminal block.  
Table B. PV140 to RJ-45 Wall Block Connections  
RJ-45 Wall Block  
PV140 Signal  
To Pin  
Signal  
TX+  
RX+  
RX-  
TX-  
TX+  
1
2
7
8
TX-  
RX-  
RX+  
USB to RS-232 Cable: A USB to RS-232 converter cable (with a DB9 male connector) is included with the KBD300USBKIT. The cable  
connects the PV140 to the DX4500/DX4600.  
ABOUT SOFTWARE UPDATES FOR THE DX4500/DX4600  
Before you begin updating your DX4500/DX4600, be sure to observe the following information:  
Your current DVR configuration settings are not deleted or replaced during the update process.  
Download the required update files from www.pelco.com.  
Your unit might require more than one update. Refer to the DX4500/DX4600 product label for the units version (1.2, V1.3, or A1.3). Then  
refer to Table C on page 10 for the required update files and procedures.  
You must use a USB drive to update the DX4500/DX4600 firmware and software. The update file must be the only file on the USB drive, and  
it must be located in the USB drive root directory.  
C2968M-A (10/09)  
9
 
       
Table C. DX4500/DX4600 Update Paths  
Version  
DX4500/DX4600 Description  
Update Files  
1.2  
Version 1.2 hardware cannot be updated to support Pelco C (Coaxitron) protocol.  
Pelco D and Pelco P protocols must be used to operate PTZ cameras.  
• Version 1.3 kernel  
• Version 1.3 firmware  
Units that were installed or shipped prior to the version 1.3 release are configured  
with version 1.2 firmware, kernel, and hardware. You must install the following  
updates:  
Kernel.  
Version 1.3 firmware: Includes new features except KBD300A support.  
Version 1.3 kernel: Supports the optional KBD300A keyboard.  
V1.3  
Version 1.2 hardware cannot be updated to support Pelco C (Coaxitron) protocol.  
Pelco D and Pelco P protocols must be used to operate PTZ cameras.  
• Version 1.3 kernel  
Kernel.  
Units that shipped after the version 1.3 software release are configured with the  
version 1.3 firmware and kernel on version 1.2 hardware. You must install the  
following updates:  
Version 1.3 firmware: Installed at the factory (includes new features except  
KBD300A support).  
Version 1.3 kernel: A required field update. Supports the optional KBD300A  
keyboard.  
A1.3  
Version 1.3 hardware supports the Pelco C (Coaxitron) protocol to operate PTZ  
cameras over coaxial cable. It also supports Pelco D and Pelco P protocols.  
Updates not required  
DX4500/DX4600 version 1.3 DVRs are factory-configured with the following  
software:  
Version 1.3 firmware: Installed at the factory.  
Version 1.3 kernel: Installed at the factory.  
Downloading Software Updates  
1. Go to http://www.pelco.com/software/downloads/dvr/ and locate the information in the “DX4500 and DX4600 Series” section of the page.  
2. Download the update software and copy it to the root directory of an empty USB drive.  
Updating the Firmware and Kernel  
1. Log on to the DVR at the administrator level. The DVR application window and toolbar appear.  
2. Insert the USB device.  
3. Click the Setup icon  
. By default, the Camera menu is selected.  
4. Click the System menu.  
10  
C2968M-A (10/09)  
 
     
5. From the System menu, click Update. The Update settings box appears (refer to Figure 3).  
Figure 3. Update Settings  
6. Click the Update property. The Update settings box changes color.  
7. On the front panel, press the SHIFT button, and then press the SET button. The Update dialog box appears. “MTD by default” appears in the  
image text box.  
8. Click ALL AVAILABLE, and then click OK (refer to Figure 4). When the system locates the update file on the USB drive, the system updates  
the firmware, software, and kernel. After the update process is complete, you are prompted to restart the DX4500/DX4600.  
Figure 4. Update Dialog Box  
9. Click OK. The unit restarts and is ready for you to update the application software.  
10. If necessary, repeat steps 1 through 9 to install more than one firmware update.  
NOTES:  
Your unit might require more than one update to support the KBD300A. Refer to Table C on page 10 for the required update files.  
If the system cannot find a valid update file in the root directory, the following message appears: “Cannot find valid update file.” Make sure  
the update file is in the root directory of the USB drive, and then repeat steps 7 and 8.  
Updating the Application Software  
1. Log on to the DVR at the administrator level. The DVR application window and toolbar appear.  
2. Insert the USB device.  
3. Click the Setup icon  
. By default, the Camera menu is selected.  
4. Click the System menu.  
5. From the System menu, click Update. The Update settings box appears.  
6. Click the Method settings box to display USB.  
7. Click the Update property. The Update settings box changes color.  
8. Click the Update settings box. The following message appears: “Do you want to update the DVR S/W?”  
C2968M-A (10/09)  
11  
 
         
9. Click OK. When the system locates the software update file on the USB drive, the system installs the application software. After the update  
process is complete, you are prompted to restart the DX4500/DX4600.  
Figure 5. Update Dialog Box  
10. Click OK. The unit restarts and is ready for operation.  
11. If necessary, repeat steps 1 through 10 to install more than one firmware update.  
NOTES:  
Your unit might require more than one update to support the KBD300A. Refer to Table C on page 10 for the required update files.  
If the system cannot find a valid update file in the root directory, the following message appears: “Cannot find valid update file.” Make sure  
the update file is in the root directory of the USB drive, and then repeat steps 9 and 10.  
DS CONTROLPOINT  
DS ControlPoint now supports the use of the KBD300A keyboard. You must install the KBD300USBKIT to connect a KBD300A keyboard to a  
computer that is running DS ControlPoint software.  
For information on using the KBD300A with DS ControlPoint, refer to Keyboard Features and Functions with DS ControlPoint on page 17.  
CONNECTING TO DS CONTROLPOINT  
Figure 6 shows how to connect the keyboard to the computer.  
16-INPUTS XMUX  
OR XMUX 2  
DS ENTERPRISE SAVR  
OR  
DS XPRESS W/ 64-INPUTS  
PIN 8  
PIN 7  
PIN 8  
PIN 1  
SCSI  
12 VAC  
STORAGE  
WAN/LAN  
PIN 2  
PIN 1  
PIN 8 = RX+  
PIN 7 = RX-  
.
.
.
.
PIN 2 = TX-  
PIN 1 = TX+  
Figure 6. DS ControlPoint Wiring Diagram  
12  
C2968M-A (10/09)  
 
       
WARNING: Do not connect the included PV140 power supply. The PV140 receives power from the computer and does not need a separate  
power supply.  
Computer: The computer on which DS ControlPoint is running.  
KBD300A Keyboard: Controls PTZ cameras connected to the computer. A 25-foot (7.6 m) RJ-45 cable is supplied with the keyboard.  
The RJ-45 connects the terminal block to the KBD300A keyboard.  
Keyboard Data and DIP Switch Cover: Contains the keyboard configuration switches. Use the switches to configure the keyboard  
address and operational mode (refer to Figure 7).  
1
2
3
4
5
6
7
8
ON  
DOWN = ON  
Figure 7. KBD300A Switch Settings: DS ControlPoint Operation  
RJ-45 Connector: Connects the KBD300A to the terminal block using the RJ-45 cable.  
KBDKIT/KBDKIT-X: The keyboard wiring kit that provides power for the KBD300A keyboard and interfaces the keyboard to the PV140.  
The kit includes two RJ-45 wall blocks and a 120 VAC/230 VAC to 12 VAC transformer.  
Table D. RJ-45 Wall Block Pinouts  
Pin Signal  
Pin Signal  
1
2
3
4
TX+  
5
6
7
8
GND  
N/A  
RX-  
TX-  
12 VAC/DC  
Nonpolar  
RX+  
PV140: A user-supplied interconnect cable (shielded twisted pair) is required to connect the PV140 to the terminal block.  
Table E. PV140 to RJ-45 Wall Block Connections  
RJ-45 Wall Block  
PV140 Signal  
To Pin  
Signal  
TX+  
RX+  
RX-  
TX-  
TX+  
1
2
7
8
TX-  
RX-  
RX+  
USB to RS-232 Cable: A USB to RS-232 converter cable (with a DB9 male connector) is included with the KBD300USBKIT. The cable  
connects the PV140 to the computer.  
C2968M-A (10/09)  
13  
 
     
INSTALLING THE KBD300A  
To install the KBD300A keyboard:  
1. Attach the KBDKIT power supply to the RJ-45 wall block, but do not connect the power supply to a power source. Refer to Figure 1 on  
page 8 and Table A on page 9 for information about setting up the RJ-45 wall block for a DX4500/DX4600. Refer to Figure 6 on page 12 and  
Table D on page 13 for more information about setting up the RJ-45 wall block for DS ControlPoint.  
NOTE: Do not connect the PV140 power supply. The PV140 receives power from the DX4500/DX4600 or the computer (depending on the  
installation) and does not need a separate power supply.  
2. Wire the RX-, RX+, TX-, and TX+ terminals from the PV140 to the RJ-45 wall block using a user-supplied interconnect cable (shielded  
twisted pair). Refer to Figure 1 on page 8 and Table B on page 9 for correct wiring information for DX4500/DX4600. Refer to Figure 6 on  
page 12 and Table E on page 13 for correct wiring information for DS ControlPoint.  
3. Connect the RJ-45 wall block power supply to a power source.  
4. Use the USB to RS-232 converter cable to connect the PV140 to the computer.  
5. Set up the KBD300A operation mode and address:  
a. On the KBD300A back panel, remove the two Phillips screws and the DIP switch cover.  
b. Set the keyboard to operate in CM6700 ASCII mode. Set switch 7 to the ON position (down) and set switch 8 to the OFF position (up).  
c. Set switches 1 to 5 to the OFF position (up) and set switch 6 to either the ON or OFF position.  
d. Reinstall the DIP switch cover.  
6. Connect one end of the data cable to the RJ-45 wall block and the other end to the keyboard.  
14  
C2968M-A (10/09)  
 
 
Operation  
KEYBOARD OVERVIEW  
SHIFT  
F1 / LATCH  
SEQUENCE  
F2 / OFF  
HOLD  
F3 / MOM  
ON — AUX — OFF  
MON  
1
ACK  
PREV  
NEXT  
NEAR  
PATTERN PRESET  
MACRO  
PGM  
2
5
3
FAR  
4
6
9
OPEN  
CLOSE  
7
8
CAM  
0
CLEAR  
KBD300A  
MADE IN U.S.A.  
Figure 8. KBD300A Keyboard Overview  
ᕫᕾ  
ᕫᕵ  
ᕫᕶ  
ᕫᕷ  
ᕫᕸ  
ᕫᕹ  
ᕫᕺ  
ᕫᕻ  
ᕫᕼ  
ᕫᕽ  
LED display  
MACRO (macro sequence)  
Joystick  
Shift Key LED (on/off indicator)  
SHIFT  
PRESET  
PREV (previous sequence)  
NEXT (next sequence)  
HOLD (hold sequence)  
PATTERN  
NEAR/FAR and OPEN/CLOSE: The focus and iris control keys.  
CLEAR  
F1/LATCH, F2/OFF, F3/MOM and Multiplexer Display: The  
auxiliary function control keys. When SHIFT is on (glows), the  
keys control the multiplexer display: full-screen view, single-  
pane view (1 x 1), and 4-pane view (2 x 2).  
CAM (camera selection)  
Numeric Keypad  
ACK (acknowledge)  
MON (monitor selection)  
AUX ON/OFF and Multiplexer Display: The receiver auxiliary  
control keys. When Shift is on (glows), the keys control the  
multiplexer display: 9-pane view (3 x 3) and 16-pane view (4 x4).  
PGM (program sequence)  
C2968M-A (10/09)  
15  
 
     
KEYBOARD FEATURES AND FUNCTIONS WITH DX4500/DX4600  
The KBD300A provides the following features for use with the DX4500/DX4600 Series DVR.  
JOYSTICK  
When the SHIFT LED is off (not lit), you can perform the following camera operations:  
Control the camera’s PTZ function.  
Twist the joystick clockwise to zoom in and counterclockwise to zoom out.  
Move the joystick to stop a pattern.  
Move the cursor in the on-screen camera menu.  
Menu tree: Moves the cursor up and down through the on-screen camera menu.  
Parameter selection: Sequences through the parameter choices.  
When the SHIFT LED is on (glows), use the joystick to easily select a camera pane.  
NEAR/FAR AND OPEN/CLOSE  
The NEAR/FAR and OPEN/CLOSE keys allow you to control the lens and navigate the on-screen camera menu.  
When the SHIFT LED is off (not lit), you can view video in the camera pane with the following commands:  
NEAR/FAR: Press and hold these keys to zoom the lens in or out.  
OPEN/CLOSE: Press and hold these keys to open or close the iris to lighten or darken the video.  
While displaying the on-screen menu, you can use the following commands:  
NEAR/FAR: Quickly press and release these keys to move the cursor up or down through the camera menu.  
OPEN/CLOSE: Quickly press and release the OPEN key to select a menu item; quickly press and release the CLOSE key to move the cursor  
to the Exit command.  
CAM  
When the SHIFT LED is on (glows), press a number and the CAM key to assign the selected camera to the first view pane. The remaining view  
panes are positioned in numerical order. For example, if channel 06 is the first view pane, channel 07 is displayed in the second view pane, and  
so forth.  
PRESET  
The PRESET key allows you to call up and configure camera presets. When the SHIFT LED is off (not lit), use the numeric keypad and the PRESET  
key to perform the following commands:  
Press and release a number, and then quickly press PRESET to move the camera to the configured preset position.  
Press and release a number, and then press and hold PRESET for two seconds to program the current camera position to a supported preset  
number. Preset 95 displays the camera menu.  
For more information about camera presets, refer to the documentation supplied with the camera.  
PATTERN  
The PATTERN key allows you to run both long and short camera patterns.  
Run a pattern: When the SHIFT LED is off (not lit), press and release a number, and then quickly press PATTERN to run a selected program.  
The DX4500/DX4600 supports up to four unique PTZ patterns.  
Program a pattern: When the SHIFT LED is off (not lit), press and release a number, and then press and hold PATTERN for two seconds to  
start the pattern recording mode.  
For more information about camera presets, refer to the documentation supplied with the camera.  
ACK  
When the SHIFT LED off (not lit), press the ACK key to stop the pattern recording mode.  
16  
C2968M-A (10/09)  
 
             
F1/LATCH, F2/OFF, F3/MOM, AND AUX ON/OFF  
When the SHIFT LED is off (not lit), press a number and the AUX ON key to control the auxiliary functions; press a number and the AUX OFF key to  
control the receiver auxiliaries.  
MULTIPLEXER DISPLAY  
When the SHIFT LED is on (glows), press one of the following keys to customize how video is displayed in the application window.  
Full-screen view  
Single-pane view (1 x 1)  
4-pane view (2 x 2)  
9-pane view (3 x 3)  
16-pane view (4 x 4)  
KEYBOARD FEATURES AND FUNCTIONS WITH DS CONTROLPOINT  
Table F. Keyboard Features and Functions with DS ControlPoint  
Keyboard Features  
SHIFT + ZOOM  
SHIFT + F2/OFF  
SHIFT + F3/MOM  
SHIFT + AUX ON  
SHIFT + AUX OFF  
ACK  
Corresponding DS ControlPoint Functions  
Full-screen view  
Single-pane view (1 x 1)  
4-pane view (2 x 2)  
9-pane view (3 x 3)  
16-pane view (4 x 4)  
Enters PTZ mode  
ACK + joystick  
NEAR and FAR  
OPEN and CLOSE  
Numeric Keypad and PRESET  
CAM  
Controls the pan, tilt, and zoom on selected video window  
Focuses the camera lens  
Controls the iris to lighten or darken the vide.  
Calls up camera presets  
Enters the video window navigation mode  
Navigates the video windows  
CAM + joystick  
MON  
Associates a selected camera to a selected video window  
Associates a camera to a specific video window (numbered left to right, top to bottom)  
MON + keypad  
C2968M-A (10/09)  
17  
 
       
18  
C2968M-A (10/09)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment.  
• Six months:  
All pan and tilts, scanners, or preset lenses used in continuous motion  
applications (preset scan, tour, and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to a Pelco designated location. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Exceptions to this warranty are as noted below:  
• Five years:  
Fiber optic products  
TW3000 Series unshielded twisted pair (UTP) transmission products  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelcos liability  
for any claim, whether based on breach of contract, negligence, infringement of  
any rights of any party or product liability, relating to the Products shall not exceed  
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be  
liable for any special, incidental, or consequential damages (including loss of use,  
loss of profit, and claims of third parties) however caused, whether by the  
negligence of Pelco or otherwise.  
• Three years:  
Pelco-designed fixed network cameras and network dome cameras with  
Sarixtechnology.  
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,  
C10CH Series, and IP3701H Series)  
EH1500 Series enclosures  
Spectra® IV products (including Spectra IV IP)  
Camclosure® Series (IS, ICS, IP) integrated camera systems  
The above warranty provides the Dealer with specific legal rights. The Dealer may  
also have additional rights, which are subject to variation from state to state.  
DX Series digital video recorders, DVR5100 Series digital video recorders,  
Digital Sentry® Series hardware products, DVX Series digital video  
recorders, and NVR300 Series network video recorders  
Endura® Series distributed network-based video products  
Genex® Series products (multiplexers, server, and keyboard)  
PMCL200/300/400 Series LCD monitors  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the  
following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number  
3. Details of the defect or problem  
• Two years:  
Standard varifocal, fixed focal, and motorized zoom lenses  
If there is a dispute regarding the warranty of a product that does not fall under  
the warranty conditions stated above, please include a written explanation with  
the product when returned.  
DF5/DF8 Series fixed dome products  
Legacy® Series integrated positioning systems  
Spectra III, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20  
scanners, including when used in continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which the  
item was received by Pelco.  
Esprit Ti and TI2500 Series thermal imaging products  
Esprit and WW5700 Series window wiper (excluding wiper blades).  
CM6700/CM6800/CM9700 Series matrix  
RETURNS  
Digital Light Processing (DLP®) displays (except lamp and color wheel). The  
lamp and color wheel will be covered for a period of 90 days. The air filter is  
not covered under warranty.  
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100  
or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair) and designated return location.  
Intelli-M® eIDC controllers  
PMCL542F, PMCL547F, and PMCL552F FHD monitors  
All merchandise returned for credit may be subject to a 20 percent restocking and  
refurbishing charge.  
• One year:  
Video cassette recorders (VCRs), except video heads. Video heads will be  
covered for a period of six months.  
Goods returned for repair or credit should be clearly identified with the assigned  
CA or RA number and freight should be prepaid.  
10-1-09  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
C2968M  
Date  
8/09  
Comments  
Original version.  
C2968M-A  
10/09  
Revised the DIP switches in Figures 6 and 7, and the Product Warranty.  
Pelco, the Pelco logo, Camclosure, Coaxitron, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.  
Spectra III is a trademark of Pelco, Inc.  
© Copyright 2009, Pelco, Inc. All rights reserved.  
DLP is a registered trademark of Texas Instruments Incorporated.  
All product names and services identified throughout this document are trademarks or registered trademarks of their respective companies.  
The absence of a trademark or registered trademark from this document does not constitute a waiver of intellectual property rights.  
 
Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA  
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150  
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120  
 

Pelco Power Supply C561M I 4 08 User Manual
Philips Car Video System 170V9 User Manual
Philips Cell Phone 859 User Manual
Philips Portable DVD Player PET7402S 37 User Manual
Philips Speaker System FWD798 37 User Manual
Pinnacle Speakers Gas Grill TG475 2 User Manual
Pioneer Stereo Receiver VSX 1016V S User Manual
Planar CRT Television LT1201 User Manual
ProForm Home Gym PFEL39260 User Manual
PYLE Audio Headphones PLVWH2 User Manual